Search results

  1. Richard Cook

    Replacing a pull cord extractor fan with timer extractor fan

    I think my options are A) Get a non timer fan B) Connect a small bit of wire from L to T
  2. Richard Cook

    Replacing a pull cord extractor fan with timer extractor fan

    I’m replacing an old 100mm extractor fan in the kitchen with a new one. The old one was a pull cord fan whereas I bought a timer one (no pull cord) thinking I could use the isolator switch (which is directly below the fan) as the on/off switch. The cabling is a 3 core and on the new fan there’s...
  3. Richard Cook

    Wiring outside light with 5 wires

    I think you’re totally right! I’ll report back but this makes the most sense and yes the black cable with brown and blue is from bulb 👍🏻
  4. Richard Cook

    Wiring outside light with 5 wires

    And this is what the wiring of the light looks like
  6. Richard Cook

    Wiring outside light with 5 wires

    Thanks for the help. See the attached from the instructions. One cable from light has blue and brown and the other has blue brown and red
  8. Richard Cook

    Wiring outside light with 5 wires

    Hi folks, I’m trying to fit a new outside light. From the wall is blue, brown and earth but the light itself as blue, brown, and red from the lamp and brown and blue from the PIR. Can you help?
  9. Richard Cook

    Wiring outside light with 5 wires (2 cables)

    Hi folks, I’m trying to fit a new outside light. From the wall is blue, brown and earth but the light itself as blue, brown, and red from the lamp and brown and blue from the PIR. Can you help?
  10. Richard Cook

    Ring hardwired doorbell jumper cable

    I’m looking to finally connect my Ring Hardwired doorbell. The existing bell has 4 wires going to it; two from doorbell and two from transformer at consumer unit. I’m wondering if you have any advice where the jumper cable needs to go? And to be honest I’m wanting to get rid of the bell so can...
  12. 33A467DB-47D0-41CE-9792-C70C58FD3914.jpeg

    33A467DB-47D0-41CE-9792-C70C58FD3914.jpeg

    • Richard Cook
    • Media item
    • Comments: 0
    • Category: Electrical Videos
  13. Richard Cook

    UK Doorbell chime wiring

    I went out and looked at the bell push. Think it's knackered. I removed from the wall and used a length of wire to touch the two wires and it rang the bell! I think the terminals on the bell push are corroded so have ordered a new bell push and, fingers crossed, that should be that. I really...
  15. Richard Cook

    UK Doorbell chime wiring

    Okay! So! I think we're getting somewhere. I quickly dabbed terminals 0 and 1 together and it did chime (!!!) but also got a wee spark. Should I try and swap 0 and T3 around and see if it chimes with no spark?
  16. Richard Cook

    UK Doorbell chime wiring

    Thanks again so much for the help. Attached is a photo of my multimeter. I’ve set it to AC volts and probed T1 with T3 and got 16v and then did the same with T1 and T0 and got 16.80v. I went to the transformer and did the same and got around 16.78v.
  18. Richard Cook

    UK Doorbell chime wiring

    And this is a photo of the instructions from the bell. The second option has 4 wires; two from bell push and two from transformer. Two wires were already twisted together so assumed one was from bell push and one from transformer.
  19. Richard Cook

    UK Doorbell chime wiring

    Thanks for the reply! I have a multimeter I’ve just never used one so unsure what to do?
  20. Richard Cook

    UK Doorbell chime wiring

    Thanks for the replies. I’ve done the following (see photo) as well as switch the wires around on 0 and T3 and pressing the doorbell does nothing on both occasions. Hmm.
  22. Richard Cook

    UK Doorbell chime wiring

    After further investigation I found the transformer next to the consumer unit.
  24. Richard Cook

    UK Doorbell chime wiring

    Hi folks I moved into our house a year ago and at some point I disconnected our doorbell chime and then, stupidly, managed to chuck it in the chaos of life. I normally take a photo before I disconnect anything but didn’t this time and all I have is the photo attached of 4 white wires. Does...
  25. Richard Cook

    Dishwasher needing switched off at wall to ‘reset’ before each cycle?

    I’ve got a dishwasher from IKEA (integrated into unit) and it’s under 2 years old. For the best part of since I’ve had it... when I go to turn it on it will beep (as if it’s picking up on the pressing) but it won’t show anything on the display etc. I have to switch it off at the wall and wait...
  26. Richard Cook

    Replacing bathroom pull switch with dimmable pull switch

    I agree. It’s weird that the grey cable doesn’t enter the plastic fitting. It was £30 too! Thought it would’ve been a bit more thought through...
  27. E334B449-403A-456E-9EBC-3915F58E43E5.jpeg

    E334B449-403A-456E-9EBC-3915F58E43E5.jpeg

    • Richard Cook
    • Media item
    • Comments: 0
    • Category: Electrical Videos
Tiling Forum

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

UK Tiling Forum
This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Tiling Advice
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock