Dodgy trade pictures for your amusement! - 1 Million Views! | Page 103 | on ElectriciansForums

Dodgy trade pictures for your amusement! - 1 Million Views!

Post new thread

Discuss Dodgy trade pictures for your amusement! - 1 Million Views! in the UK Electrical Forum area at ElectriciansForums.net

D

Darkwood

Right ... Just been nudged to set this up by Paul.M and sounds a good idea following recent threads I've done in the Arms..

Rules....No Offensive material... edit if required before posting as this is the public arena.
Anything to do with the trade or in and around it ...H&S pic's welcome.

[ElectriciansForums.net] Dodgy trade pictures for your amusement! - 1 Million Views!

I've posted this a few times and this is at a mates house following a kitchen refirb several yrs ago. :eek:mg_smile:

[ElectriciansForums.net] Dodgy trade pictures for your amusement! - 1 Million Views!
 
Sort by date Sort by votes
here's a good one, this was the MDB for a warehouse complex with 20 warehouses, 3 office blocks, on the right is the Utility supply incomer cabinet.
6 weeks solid work to replace and fix this up.
[ElectriciansForums.net] Dodgy trade pictures for your amusement! - 1 Million Views!

We replaced with a 250amp 250 TPN eaton load centre, steel trunking cable managment, new SDBs an ATI for generator, prior to this the loacl electrican removed the knife edge fuses and put the cable from the generator ( one hanging down) into the top holder of the KE fuse holders with a pliers.
To protect the utility supply all we could do was put 12mm perspecx sheets affixed to the dexion frames. Utility provider considered it safe in its orignal state and would not replace it with the unit we bought for them.
 
Upvote 0 Downvote
Deleted as no pictures!

[ElectriciansForums.net] Dodgy trade pictures for your amusement! - 1 Million Views!


[ElectriciansForums.net] Dodgy trade pictures for your amusement! - 1 Million Views!

Not electrical but I’m on the job so that counts.
Skirting board taken off to reveal the nail had punctured the central heating pipe but NOT caused any leak. Whether it was a tight puncture and sealed itself with lime scale is unknown but no damage seen in the area.
How sweet is that!
 
Last edited:
Upvote 0 Downvote
Lucky escape there! When I got a flat a couple of years ago the "plumber" was finishing off installing a shower, and put the outside frame on and off he went...thursday night before the september weekend, so no-one was about until I arrived on the next tuesday to meet all my downstairs neighbours paddling about in wellingtons. He had driven a screw into the cold supply pipe for the shower and it had leaked all weekend...
Certainly got to meet the neighbours!
I could go on about his reluctance to use pipe inserts with push-fit connectors...but I'll save you the angst!
 
Upvote 0 Downvote
littlespark said:
Don't tell the heating engineers forum, but on a loft conversion I'm doing, I've done the electrics and added 4 radiators to the guys heating system. Customer is an old school friend and he said he was having trouble getting someone.... I didn't touch the gas... it was only on the flow and return pipes
Click to expand...

The original heating installation would have been specified and designed given the number and size of radiators that were installed. Did you take that into account before adding the extra 4 rads? We go ballistic when amateur electricians overload a previously sound installation based on their little bit of knowledge. Just saying.
 
Upvote 0 Downvote
dksanders said:
The original heating installation would have been specified and designed given the number and size of radiators that were installed. Did you take that into account before adding the extra 4 rads? We go ballistic when amateur electricians overload a previously sound installation based on their little bit of knowledge. Just saying.
Click to expand...

Good point, however;-
The customer had already replaced the boiler previously after original broke down. He asked for a bigger model knowing that the loft conversion was on the cards. The heating engineer at the time had done the measurements and given him sizes of rads to buy.
And I'm not an amateur electrician... I'm a professional electrician.
Amateur at everything else. - Just saying
 
Upvote 0 Downvote
Maybe...
IDC totally wrong shape for those...
Anyway, not an expert on that...or on anything, but insulation displacement may be fine for 5V, but anything more and I would be worried!
Funny, but those IDC things are so prone to working loose, just a wiggle or two and contact is lost...and when you see them stacked up...
 
Upvote 0 Downvote

Reply to Dodgy trade pictures for your amusement! - 1 Million Views! in the UK Electrical Forum area at ElectriciansForums.net

News and Offers from Sponsors

PCBWay
  • Article
Meet PCBWay at electronica A1.163
Join us at electronica 2024 in Munich! Since 1964, electronica has been the premier event for technology enthusiasts and industry professionals...
    • Like
Replies
0
Views
323
PCBWay
PCBWay
Electrical2go
  • Sticky
  • Article
📢 Best Sellers Catalogue Now Available! 📢
Good to know thanks, one can never have enough places to source parts from!
Replies
4
Views
851
Bob Labla
B
Dan
  • Article
The Official Sponsors of ElectriciansForums - There are currently 8
OFFICIAL SPONSORS These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then...
Replies
0
Views
973
Dan
Dan

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top