some body bang on the door some body ring the bell

buzzlightyear · Oct 12, 2018

having been to a hotel with a fault on a lights and open and close system on a circuit .I had fixed the fault in which was the lighting .and Elvis left the building. about 1 hour after me left the building .
the customer rings up the entry will not work .well it work for going out
back to faulty towers again .
now this card reader has a fault on it .and want read any cards
I have now trying to get a replacement card reader I have posted the reader
so any of the gang to point me in the write direction.

[ElectriciansForums.net] some body bang on the door some body ring the bell

123 · Oct 12, 2018

And if your spelling is as bad as it is on here on an internet search, not surprised you haven't been able to find anything

Dave OCD · Oct 12, 2018

I once went out with a lovely girl who had Dyslexia, we went back to her place once and she cooked my sock.

buzzlightyear · Oct 12, 2018

123 said:
Get a company that specialises in door access etc to sort it. I doubt the hotel would be too happy to wait whilst you search the internet to find and source a replacement unit that could take a few days or longer to arrive, and might not even be the problem

may be you are correct .
I ring them in the morning and tell them the bad news .if I was not for the fault on the light out side it would not happen you should have seen the way some body wired the out side lights straight from 16amp mcb no fuse spur knout. and this a hotel .

littlespark · Oct 12, 2018

Did you get power back onto the door entry system?
Are you sure its the reader and not the opening part of the system?
(I've only installed a card reader system with a magnetic lock, not a fully automatic opening door)
Does the cards make a noise when used? An accept, or different reject beep noise?

I had to change the mag lock to a "fail safe" lock rather than a "fail secure"
The difference being when there was a powercut, the door would unlock instead of locking. Which, on a caravan site toilet block was the preferred choice.

Doomed · Oct 12, 2018

If its a card reader there will be another box ox tricks somewhere that you may of switched off, or cleared its memory.
Could be a little box with a keypad, could be an ethernet connection to a pc, but there will be a way of programming the cards somewhere, which I have seen hooked into the lighting circuit sometimes.....

buzzlightyear · Oct 12, 2018

123 said:
Get a company that specialises in door access etc to sort it. I doubt the hotel would be too happy to wait whilst you search the internet to find and source a replacement unit that could take a few days or longer to arrive, and might not even be the problem

may be you are correct .
I ring them in the morning and tell them the bad news .if I was not for the fault on the light out side it would not happen you should have seen the way some body wired the out side lights straight from 16amp mcb no fuse spur knout. and this a hotel .

buzzlightyear · Oct 12, 2018

Doomed said:
If its a card reader there will be another box ox tricks somewhere that you may of switched off, or cleared its memory.
Could be a little box with a keypad, could be an ethernet connection to a pc, but there will be a way of programming the cards somewhere, which I have seen hooked into the lighting circuit sometimes.....

their was new card made for the opener and old card used and still knowt. by passed the card reader magnets opened it

electric al · Oct 12, 2018

reminds me of the dyslexic house party that was raided by the cops -police confiscated a load of " F " s

Midwest · Oct 13, 2018

Was it this song you were after?

littlespark · Oct 13, 2018

#22
Is that a link between GND and NC? Doesn't look right to me.
+12v and GND gives the reader its power.
The switching part is between COM and NC.. Normally Closed until card is introduced, then opens for a time.

Usually no connection between the power and the switching parts?

(I cant be 100% sure, I don't know the system you've got there, or seen a diagram)

buzzlightyear · Oct 13, 2018

littlespark said:
Is that a link between GND and NC? Doesn't look right to me.
+12v and GND gives the reader its power.
The switching part is between COM and NC.. Normally Closed until card is introduced, then opens for a time.

Usually no connection between the power and the switching parts?

(I cant be 100% sure, I don't know the system you've got there, or seen a

this system has been installed by a engineers and that how it set up .it been a lot of years .

Squid · Oct 13, 2018

The invoices must be entertaining.........

buzzlightyear · Oct 13, 2018

SWD said:
The invoices must be entertaining...

I only went to sort the fault ,and now fault on door entry .FFS.

Squid · Oct 13, 2018

Problem exists between door entry sensor and toolbag.........

buzzlightyear · Oct 13, 2018

buzzlightyear said:
possible ,the customer kept trying new cards and none worked .good for going out by pressing the button going out . but cards don't work for some reason for entry .

what is so DUMB about that Mrs Robinson

some body bang on the door some body ring the bell

buzzlightyear

-

123

-

Dave OCD

-

buzzlightyear

-

littlespark

-

Doomed

-

buzzlightyear

-

buzzlightyear

-

electric al

-

Midwest

-

littlespark

-

buzzlightyear

-

Squid

buzzlightyear

-

Squid

buzzlightyear

-

Similar threads

Recommended Sponsor News

Quickwire Now Sponsor ElectriciansForums.net

Exclusive Forum Offer! Free euro 2024 wall chart for first 10 responses!

PCBWay Now Sponsor ElectriciansForums.net!!

OFFICIAL SPONSORS

YOUR Unread Posts