1950s IM Power Relay Timer Help for Solenoid Valves

murd_the_nerd · Feb 24, 2022

Hi there

Complete novice electrical wise. I am refurbishing an old 1950s Injection Moulding machine and looking to replace the Power Timer Relays. So far with no success myself and two attempts. It appears I need some expert help. I would love direction on the type of timer I need and a link to where I could purchase is a bonus. Any help much appreciated. Details below:

The old Timers:

[ElectriciansForums.net] 1950s IM Power Relay Timer Help for Solenoid Valves

What I've investigated:

There are 2x Timers, one for inject and one for clamp
They are both the same, because I can swap them around and it still runs just fine
Markings still remaining on one says Supply 230 V AC and Rating 6A 230 V AC. There is no cut down in power on this machine, 240V throughout.
They appear to be short-circuit driven (not power on all the time and Start commands etc)
Power is only supplied when they run and is instantly straight through to the output
11 pin circular configuration
Phase to pin 2, Neutral to pin 10
Power into pin 5 and 2 makes the output run forever until short-circuited. I think I've heard this called an Inhibit function which allows the Timer to pause and force power through pin 6. In the clamp instance this forces the clamp closed, lets the inject sequence run, and then allows the Timer to run before cutting power and releasing the clamp.
Pin 6 is the only output. This runs to the 5/2 solenoid valves and changes the valve position for either inject or clamp
Timer appears to be a Power Off Delay or similar as it only tells it when to cut power off

Diagrams that I've mapped to help explain how the Timers work and current wiring:

If you need any more info I'm happy to provide. And even if you are just interested in the machine I can post pictures of that also

Thanks
Murdoch

Lucien Nunes · Feb 24, 2022

Interesting... will take a closer look later. Might be a silly question but if the relays work, why are you replacing them?

I am not sure what you mean by 'short-circuited' as far as the output is concerned. I would read that as a short between line and neutral that would blow the fuse, but clearly you mean something else. Can you please clarify...

brianmoooore · Feb 24, 2022

This sounds like one that might interest Lucien!
Relays and timers, etc that use this style of plug in base are still available today, but to preserve originality, you're probably going to have to carefully open up the faulty one and see what the problem is. If beyond repair, there's plenty of room to fit a modern replacement inside the can an seal it up again'

Edit: I see I was right! Lucien has replied while I was typing this.

murd_the_nerd · Feb 24, 2022

brianmoooore said:
This sounds like one that might interest Lucien!
Relays and timers, etc that use this style of plug in base are still available today, but to preserve originality, you're probably going to have to carefully open up the faulty one and see what the problem is. If beyond repair, there's plenty of room to fit a modern replacement inside the can an seal it up again'

Edit: I see I was right! Lucien has replied while I was typing this.

Thanks brianmoooore, yes I've seen Lucien has replied so hope they can help

I've tried two 11pin new timers and failed so getting the right one is the challenge

murd_the_nerd · Feb 24, 2022

Lucien Nunes said:
Interesting... will take a closer look later. Might be a silly question but if the relays work, why are you replacing them?

I am not sure what you mean by 'short-circuited' as far as the output is concerned. I would read that as a short between line and neutral that would blow the fuse, but clearly you mean something else. Can you please clarify...

Hi Lucien

Thanks for replying. Yes they do actually still work and I can run the machine through a full sequence. Unfortunately the dials and knobs and internals are all a bit knackered. So each time I come back to the machine it has vibrated and the dials moved around or if I tighten too hard it goes past and spins the case. So in short, repeatability so that when I get molds I can simply set it to 2 for example and it is 2

Sorry I'm not fully up on the electrical lingo (a designer myself). But basically I'm trying to describe that there isn't power to these timers all the time like more modern versions of the 11pin. The modern ones appear to have power all the time and then trigger a start sequence. Where as these old ones appear to just get up and running once the power is applied to either 2 or 2 and 5. Then outside of itself in the sequence it is tripped and power disconnected. Does that make sense?

The two timers I have tried and failed with are:
H3CR-A (knock off version of this link below)

H3CR-A Solid-state Multi-functional Timers/Specifications | OMRON Industrial Automation New Zealand

Solid-state Multi-functional Timers Multiple Operating Modes and Multiple Time Ranges. DIN 48 x 48-mm Multifunctional Timer.

www.omron-ap.co.nz

TR-6162U

https://www.macromatic.com/product/tr-6162u

Here's a look inside the cabinet:

And machine if of interest:

marconi · Feb 25, 2022

Could you tell us what is stamped on the plate circled A? See attachment.

Circled at B are the connections to pins of a device; which one? Could you show these too if they refer to the relay you wish to source new?

murd_the_nerd · Feb 25, 2022

marconi said:
Could you tell us what is stamped on the plate circled A? See attachment.

Circled at B are the connections to pins of a device; which one? Could you show these too if they refer to the relay you wish to source new?

Hi Marconi

Sure, here is a close up of the stamp and my guesses:

Type: ET P1 TIME
Ref: R1783 0.2-5 SECS
Supply: 230 V50 AC
Rating: 6A 230 V AC

And as for some new ones I'm wondering about there are these:

Macromatic Analag Timer TAA2U

https://www.macromatic.com/product/taa2u

https://www.macromatic.com/uploads/files/pdf/instruction_sheets/taa2u-instruction_sheet.pdf

Autonics AT11EN

https://www.tme.eu/Document/fa6dbf2ce3d5b661df3c8baf339e7b8a/AT11N-series-INS.pdf

From my understanding the numbers 3, 4, 8, 9 are internal to the Timer. But where I struggle is, what is considered an Output and Input. Because from the looks I require Input to 5 to inhibit. And then I want 6 as the Output to the solenoid valve. I also see the - and + are the other way around on these timers.

Any help appreciated

marconi · Feb 26, 2022

I

murd_the_nerd said:
Hi Marconi

Sure, here is a close up of the stamp and my guesses:

Type: ET P1 TIME
Ref: R1783 0.2-5 SECS
Supply: 230 V50 AC
Rating: 6A 230 V AC

View attachment 95470

And as for some new ones I'm wondering about there are these:

Macromatic Analag Timer TAA2U

https://www.macromatic.com/product/taa2u

https://www.macromatic.com/uploads/files/pdf/instruction_sheets/taa2u-instruction_sheet.pdf
View attachment 95471

Autonics AT11EN

https://www.tme.eu/Document/fa6dbf2ce3d5b661df3c8baf339e7b8a/AT11N-series-INS.pdf
View attachment 95472

From my understanding the numbers 3, 4, 8, 9 are internal to the Timer. But where I struggle is, what is considered an Output and Input. Because from the looks I require Input to 5 to inhibit. And then I want 6 as the Output to the solenoid valve. I also see the - and + are the other way around on these timers.

Any help appreciated

I will study these over the weekend. I have found this firm which does a wide range of 11 pin timers both electronic and mechanical. There are others of course. Just need to determine the functionality and pin out to select the correct replacements:

Foxtam Electronic Timers - Foxtam Controls - https://www.foxtamcontrols.co.uk/products/foxtam-electronic-timers?gclid=CjwKCAiAvOeQBhBkEiwAxutUVHSvHPRKJ82h19_XRP_x6cjnG9xgrFnutB03_ZHWCQ_b9qyrUHY_OhoCuRoQAvD_BwE

marconi · Feb 26, 2022

mud_the _nerd: Do you have a multimeter with an 'Ohms' range? If not could you buy a cheap digital one?

If you look at the attachment you will see two identical tables. The numbers refer to the pins on the relay. Using a multimeter please measure first the resistance between pin 1 and then to each of pins 2 to 11 of the black round timer and enter the meter reading in the table. Then do the same for pin 2 but this time to pin 1 and the each of 3 to 11. Then pin 3 but to 1 then 2 and then each of 4 to11, etcetera.

The first table is for when the timer is set to zero seconds. The second table for when it is set to say 5 seconds.

The resistance between the pins will be a low value apart from I think between pins 2 and 10.

I hope this is clear. Then return the two tables to me as an attachment.

brianmoooore · Feb 26, 2022

Chances are that there is a modern version of what you want available, but it will likely be more sophisticated than the original, with unwanted additional functions built in. These you may have to disable, or ensure that they are not accidentally enabled.

marconi · Feb 26, 2022

Further to my last post; could you remove the black T1 and the white timer T2 and the heat relay and then take a photo of the wiring to their bases? Also take a clear picture of the terminal block so I can see which wire goes in to which terminal and to where the other ends go on the three relay bases.

Or you could do the wire tracing for me and send me a diagram. Do you have the manual for the machine with its wiring diagram inside?

murd_the_nerd · Feb 27, 2022

marconi said:
Further to my last post; could you remove the black T1 and the white timer T2 and the heat relay and then take a photo of the wiring to their bases? Also take a clear picture of the terminal block so I can see which wire goes in to which terminal and to where the other ends go on the three relay bases.

Or you could do the wire tracing for me and send me a diagram. Do you have the manual for the machine with its wiring diagram inside?

Thanks so much for looking into this. I don't have a multimeter but I think I will buy one so I can test for you.

I actually stumbled on this article which might shed some light. It looks like timers that old might have been True Off Delay timers rather than more modern Off Delay timers. https://www.macromatic.com/blog/relays/what-is-a-true-off-delay-function

"Upon application of input voltage, the output is energized. When the input voltage is removed, the time delay (t) begins. At the end of the time delay (t), the output is de-energized. Input voltage must be applied for a minimum of 0.1 seconds to assure proper operation. Any application of the input voltage during the time delay (t) will reset the time delay. No external trigger is required."

From a search I can find some 240v 8pin ones of these. But I haven't found a 240v 11pin version. Do you know how I would test to see if a True Off Delay or not?

I do have my own attempt at a wiring diagram. I can confirm the numbers the timers are using as I took off the timers to record where the wires went:

Please keep in mind it is only the black large old timers that work. But I found some old pictures I have of inside the cabinet:

marconi · Feb 28, 2022

Very good! I will study today. The use of pins 5 and 6 which are normally open contacts which close during the delay period, indicates as you say delay off. I will be able to find you suitable timers.

marconi · Feb 28, 2022

I have asked FOXTAM for a quote to supply two 11 pin true delay off timers from this range:

https://www.foxtamcontrols.co.uk/assets/img/25-YRKF-8RKF-11RKF-8R2KF-11R2KF.pdf

The timer above does not require a 230V ac power supply to be present to maintain the contacts closed during the delay off period.

I will also look at other suppliers such as RS components.

I will explain later how you can use three lamps connected to the terminal strip to confirm the functionality of the timers. You do not now need to fill in the connection matrices I mentioned earlier.

marconi · Feb 28, 2022

murd_the_nerd:

Please remove the wires marked with a short blue dash in the attachment called 'disconnection'. Label them so you know were to connect them back to. Put the ends of these wires inside a connector so they do not touch anything. This will disconnect the valves and the heater.

Buy three neon lamps like these:

IND5032405-240-T/RD | CAMDENBOSS Red Indicator, 240V, 8mm Mounting Hole Size, Lead Wires Termination | RS Components - https://uk.rs-online.com/web/p/indicators/0576181?cm_mmc=UK-PLA-DS3A-_-google-_-CSS_UK_EN_Displays_%26_Optoelectronics_Whoop-_-Indicators_Whoop-_-576181&matchtype=&aud-832474874771

la-302376642891&gclid=CjwKCAiAgvKQBhBbEiwAaPQw3PKQPeh7zExzTVve1WMoT2jRpbFI38x3yiulbOparbQKTL-P_mZxfxoC1tgQAvD_BwE&gclsrc=aw.ds

They are 230V ac neon indicators pre-wired with leads. Amazon will do them.

Labels these indicators as L1, L2 and L3. Now connect these lamps as I show in the second attachment 'ThreeLamps'. The leads go to the terminals at which you had disconnected a wire and the neutral.

You can now run the control panel and the lights will indicate power being supplied to the two valves or heater so that we can confirm the functionality of T1 and T2 as True Timed Delay off.

1950s IM Power Relay Timer Help for Solenoid Valves

murd_the_nerd

Lucien Nunes

-

brianmoooore

-

murd_the_nerd

murd_the_nerd

H3CR-A Solid-state Multi-functional Timers/Specifications | OMRON Industrial Automation New Zealand

marconi

-

Attachments

murd_the_nerd

marconi

-

marconi

-

Attachments

brianmoooore

-

marconi

-

murd_the_nerd

marconi

-

marconi

-

marconi

-

Attachments

News and Offers from Sponsors

Similar threads

OFFICIAL SPONSORS

YOUR Unread Posts