Hi guys, I’m looking for advice. I’m trying to figure out how to replicate a rotating light in a customers lighthouse. Had a look at spinning beacons but obviously they would be too fast. The lighthouse is glass fibre and hollow up the middle with just over 300mm diameter in the Perspex head to fit a light so getting a cable up would be no bother. I’m just struggling to find anything that could spin slowly like a real lighthouse.
![[ElectriciansForums.net] Lighthouse spinning light](https://www.electriciansforums.net/attachments/217d292b-36f5-4f7e-a828-d6f82b36c548-jpeg.97288/ "[ElectriciansForums.net] Lighthouse spinning light")
-
Please checkout our new DIY Forum, and any trade that'd like to join and help out, and Contractor Talk Forum.
- Thread starter Euan Thomson
- Start date
- Replies 15
- Views 3K
Discuss Lighthouse spinning light in the UK Electrical Forum area at ElectriciansForums.net
Generally speaking, if you want slow rotation (as in tens of seconds per revolution) you will need to gear a motor down to drive the reflector.
Small DC motors are easy to speed-regulate by adjusting the voltage which would help, but generally they have shaft speeds of a thousand rpm or thereabouts, maybe adjustable to a few hundred, so you would need probably two or three stages of gearbox to bring it down.
Something like this has a fairly slow speed at full voltage:
You might find a clock mechanism that is cheaper, etc, but maybe too slow in that case.
Small DC motors are easy to speed-regulate by adjusting the voltage which would help, but generally they have shaft speeds of a thousand rpm or thereabouts, maybe adjustable to a few hundred, so you would need probably two or three stages of gearbox to bring it down.
Something like this has a fairly slow speed at full voltage:
You might find a clock mechanism that is cheaper, etc, but maybe too slow in that case.
As an Amazon Associate Electricians Forums may earn a small commission from qualifying purchases.
Alastair Campbell holding an LED torch?
I will try harder with some potential ideas.
A few Qs:
1. What is supply voltage and frequency?
2. Is it complete top structure which rotates or just the metal axle one can see through the perspex?
3. How bright? Do you want a 'flash' of light as it swings through a bearing which would require some lenses or reflectors to direct the lamp light?
I will try harder with some potential ideas.
A few Qs:
1. What is supply voltage and frequency?
2. Is it complete top structure which rotates or just the metal axle one can see through the perspex?
3. How bright? Do you want a 'flash' of light as it swings through a bearing which would require some lenses or reflectors to direct the lamp light?
You can buy an off the shelf rotator designed to spin theatrical mirror balls with a few quick searches - I'd suggest a 4rpm one would be about right. All you'd need to do then would be to figure out how to mount a 650W DWE style lamp onto it which I'd guess you could do by butchering anything which already has a brush/ring arrangement - maybe an old motor armature.
This sounds like a fun project.......if you have the time!
This sounds like a fun project.......if you have the time!
OP
Thanks for all the input guys, definitely gave me more ideas.
@marconi input voltage will be 240v 50hz fed from an outdoor socket initially and was thinking of using a click remote to switch on and off. There’s the option of fitting a control box out with the lighthouse. The metal axle you see is a bit of threaded rod that is connected to the very top and through to the base. The base connection has fell off so I was thinking of removing the rod completely and fixing the base to Perspex to top. As for brightness and lenses I was thinking the simpler the better as it is only sitting in the customers enclosed garden.
@marconi input voltage will be 240v 50hz fed from an outdoor socket initially and was thinking of using a click remote to switch on and off. There’s the option of fitting a control box out with the lighthouse. The metal axle you see is a bit of threaded rod that is connected to the very top and through to the base. The base connection has fell off so I was thinking of removing the rod completely and fixing the base to Perspex to top. As for brightness and lenses I was thinking the simpler the better as it is only sitting in the customers enclosed garden.
Last edited:
Barbers pole light might be the right speed
How authentic does it need to be? Something like a speed adjustable strobe light mounted just below the Perspex top would replicate the flash every few seconds and would be pretty simple with no moving parts.
Cheap to run and environmentally friendly?
If it was me I would only send safe 12V along the cable to the lighthouse and keep 230V - 12V double insulated conversion inside a box on the wall or inside the building.
A possible 12/24V option if you could wire the motor separately from the bulb, to a lower voltage, or a speed controller
(and ditch the cover!)
The drive reminds me of the early Japanese "toy" tape recorders -no capstan - just driving the spool!
(and ditch the cover!)
12V 24V Rotating Amber Beacon Light Lamp Lorry Car Van Tractor Forklift Digger | eBay
12V 24V ORANGE AMBER ROTATING. RECOVERY HAZARD LAMP BULB INCLUDED H1. With Protection Cover. Simple design and easy to use. Permanent Mount : 3 Bolts. Bulb Included (H1).
www.ebay.co.uk
The drive reminds me of the early Japanese "toy" tape recorders -no capstan - just driving the spool!
As an eBay Associate we earn from qualifying purchases.
OP
Update.
The lighthouse is fully functioning. Got a IP rated 12v beacon and wired up the motor to a speed controller, however it was still too fast. Replaced that motor with a geared motor however the base needed modifying to hold the motor, oh and the motor shaft also needed turned down on my dads lathe to work. Fitted a 24v lamp to the beacon and kept all the power supplies inside an IP junction box with a click remote and receiver switching the power to the box.
I haven’t seen it working in the dark but the customer says she can see it from the opposite side of the garden, the garden is huge at least 60m. Hopefully get a video from them soon.
Thanks for all the input guys it’s very much appreciated, sparks truly are the finest trade.
The lighthouse is fully functioning. Got a IP rated 12v beacon and wired up the motor to a speed controller, however it was still too fast. Replaced that motor with a geared motor however the base needed modifying to hold the motor, oh and the motor shaft also needed turned down on my dads lathe to work. Fitted a 24v lamp to the beacon and kept all the power supplies inside an IP junction box with a click remote and receiver switching the power to the box.
I haven’t seen it working in the dark but the customer says she can see it from the opposite side of the garden, the garden is huge at least 60m. Hopefully get a video from them soon.
Thanks for all the input guys it’s very much appreciated, sparks truly are the finest trade.
Attachments
![[ElectriciansForums.net] Lighthouse spinning light](https://electricians.s3.eu-west-1.amazonaws.com/data/attachments/66/66162-66df8a9c174bc0e4ea5ee3518f3c958e.jpg)
![[ElectriciansForums.net] Lighthouse spinning light](https://electricians.s3.eu-west-1.amazonaws.com/data/attachments/66/66163-a574d344ee40d4464587e8a0289a4256.jpg)
Diane Abbott with a 10watt LED bulb in her gob. turn her on a rail engine turntable.
Reply to Lighthouse spinning light in the UK Electrical Forum area at ElectriciansForums.net
Similar Threads
Good one . Thanks. I was finding Fluke etc £££!
- Drew23
- Electrical Engineering Chat
- 5
- 2K
- Question
Youre in the same boat as me. I was previously with niceic and later on, napit. No issues. I didn't bother finishing my nvq3 as in 2010 during the...
- Question
My insurance initially went up due to a similar conversation. Asked for manual quote from underwriter and once i spoke to a decent one, it...
I do a lot of dimming with large residential systems and they are largely triac-based. They work well and are almost always LED-based these days...
We have a garden footpath 16m from front door to garden gate with a shed near the gate.
I am looking for the following set-up:
a) an independent...
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
YOUR Unread Posts
-
-
Spur/Junction for outdoor socket for PHEV charging?They are breaking the law not having an EICR carried out. You can connect from the ring final...
- Latest: westward10
-
This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.