Search results | Page 4

Search results

  1. gazdkw82

    Understanding faults/readings

    Really useful lucien. Thankyou
  2. gazdkw82

    Understanding faults/readings

    You are exactly right, the reading I got was >0.00 megaohms L/N to cpc. I didnt investigate further as to how long the reading actually was. The odd thing is that the low reading is only when the other 2 lines are connected, disconnect all 3 lines and the line from the JB is over range on the...
  3. gazdkw82

    Understanding faults/readings

    Yes i agree. This is why I'm confused. Theoretically a dead short should operate the mcb, unless I'm reading through something. I'm using a metrel MI3000 for I/R testing. I cant remember the exact voltage at the JB but it was within nominal voltage. Nothing unusual about the voltage. I cant...
  4. gazdkw82

    Understanding faults/readings

    Not sure what else I can do. I cant trace the 2 other feeds as the premises is too vast.
  5. gazdkw82

    Understanding faults/readings

    I suspected the same. When I disc the conductors from the DB the I/R readings were over range so I know the 3 conductors from the JB to the DB are fine. Disc the other 2 lines and neutrals and I get dead short on the 3 conductors at the JB, disc them from the DB and the tester wont test the 3...
  6. gazdkw82

    Understanding faults/readings

    A while back a had an issue with a commercial install I had done for a family members unit Long story short, 5x50w led floods controlled by 4 robus PIR detectors. Also a 3 way switch for option to turn off, perm on and PIR sensors. I tested the circuit prior to any work and all the readings...
  7. gazdkw82

    Blue pipe connections under build

    Thanks for the reply. What they did in the end was sleeve the joints and concrete over. Tbe building inspector said it was satisfactory so I cant really say much else
  8. gazdkw82

    Advice needed

    Because I made the assumption the OP was replacing or repairing lights and after the works was complete the lights would need to be working. But that was an assumption. Until we know exactly what work is being carried out we have no way of knowing how important the tripped breaker could be. It...
  9. gazdkw82

    Advice needed

    I understood the lighting the OP wants to work on is being supplied via this property that he has no access too? If that is the case, my point stands, if he attempts the work and trips the breaker then how will he re energise?
  10. gazdkw82

    Advice needed

    Going to be even worst if you do the work but trip a protective device. How do you then plan to turn them back on?
  11. gazdkw82

    Henley Block inside fuse box ...:)

    I really wish I could bring myself to watch his videos. It's just his voice and demeanor. I cant stomach it. Droany voice and smug face. I'm sure he is a lovely guy and a quality sparks but he dont hold my attention
  12. gazdkw82

    Henley Block inside fuse box ...:)

    The alarms rang pretty quickly for me with Del.
  13. gazdkw82

    Blue pipe connections under build

    Builders broke ground today with the digger down the side of the house. They busted a lead water pipe which runs down the side of the house. Houses are fed in bunches of 5 from the street. That means me and 4 other houses share the same stop tap. Builders repaired the T joint and replaced...
  14. gazdkw82

    Remove forum trainee badge now im qualified?

    So how do I navigate to this section from tbe main forums page? Also, when I click the "apply to gain access" link it opens an orange page advertising electrical courses
  15. gazdkw82

    Remove forum trainee badge now im qualified?

    Ok, I'll get you a scotch egg
  16. gazdkw82

    Remove forum trainee badge now im qualified?

    Yeh I'm pretty late to the party but I'll make up for lost time with a round on me ?
  17. gazdkw82

    Remove forum trainee badge now im qualified?

    Ah ok. Makes sense now. Would like access to the arms if possible ?
  18. gazdkw82

    Remove forum trainee badge now im qualified?

    Meaning?
  19. gazdkw82

    Remove forum trainee badge now im qualified?

    Not all members of the trainee section are "super experienced"
  20. gazdkw82

    Remove forum trainee badge now im qualified?

    What does arms access mean?

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top