Please see attached electrical art. Please study and note my remarks beside the three balloons. The ohmmeter tests at A, B,C and D must be done with all sources of electrical energy ie mains, battery and pv panels isolated. With ohmmeter set to low range eg 0 to 200 measure between N and E/cpc...
The switching inside the inverter box is normally done by solid state switches to ensure no-break of supply when moving between mains to output or inverter to output.
Tonyboy - where have you happened upon the term TN-S? I suspect what you have bought or set up is an off grid systemwith genie...
Please could you clarify the bit in bold in:
. The AC loads are connected a fully protected AC output plug , there is one 30mA 40A, RCD and MCB with TN-S earthing arrangement (common Neutral to Ground).
On the inverter load side including what you may have connected to it have you connected...
It would be interesting to know what happens when:
a. All the LED final circuits are supplied by the new BG RCBO;
b. you swap back the current BG LED final circuit to the original mcb and connect up one of the other LED finals to the BG RCBO;
c. you supply all the LED finals via a new Click...
I went to a venue in Essex today to size up high tea for my wife's 60th with her friends. Sort of venue that specialises in weddings normally but does hotel, dinner and other events too eg today a post funeral tea. Posh sort of place.
As we had our Jack Russell I wandered around the grounds...
Sentences as you state. The more culpable in law was the duty holder who was the landlord and owner. He failed to discharge his duties as required by shef law even though he knew what was required. The last link I sent says more.
Pub owner jailed over boy's electrocution death 28 May 2021 - Article from Forbes Solicitors - https://www.forbessolicitors.co.uk/news/47618/pub-owner-jailed-over-boys-electrocution-death
Try putting the LED lighting mcb/rcbo right next to the mainswitch/rcd. If a dual RCD board put LED lighting mcb/rcbo on the side with lower loading. Voltage dips can cause LEDs and LEDs + DImmer to flicker.
I will have another think. Do your neighbours with LED lighting experience the same problem? You will need to ask at several homes to cover all three phases.
And a temperature factor?
https://www.varilight.co.uk/leaflets/VARILIGHT V-Pro Dimmer Instructions JP003.pdf
Take a look at the reference and the section called 'Overview' at the link above. It explains how to change between one of three modes of sine wave switching. The default setting is Mode 1 - trailing edge but...
pc1966 - the sort of reading material I was weaned on. I have to say, that like many engineers, I was glad when 'electronic functionality' did not have to be designed and built from scratch each time, and instead one could take ics with reliable and repeatable functionality and combine them...
A coder/decoder or multiplexer/demultiplexer can do BCD to 10 lines one hot or vice versa provided that 4 bits are used for the binary input/output. Three bit words only covers the numbers 0 to 7 and therefore cannot cover the decimal numbering system which uses 0 to 9.
I am glad you are...
The 4028 can be cascaded. See Figures 13 and 15 in this link:
https://www.ti.com/lit/ds/symlink/cd4028b.pdf?ts=1673700179941&ref_url=https%3A%2F%2Fwww.ti.com%2Fproduct%2FCD4028B
The 4028 is a 3 bit binary to 8 line one-hot or 4 bit binary coded decimal ( 0 to 9 in 4 bit binary ie 0000 to...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc