Search results

Search results

You will need 50 posts under your account before joining in with this thread because you can't link out without 50 posts first.

  1. Pat H

    SPD in a plastic consumer unit.

    Adding an EC charger and looking at options to include an SPD. The consumer unit is plastic (but in good condition) Options seem to be to add an SPD (with isolator and MCB) before the consumer unit. Or add an isolator before the EV charger with an SPD, isolator and MCB. Or can an SPD be added...
  2. Pat H

    Cable tray supports needed

    Thanks. Yes that's the simple solution.
  3. Pat H

    Cable tray supports needed

    I'd need a C shaped one or my tray will end up vertical rather than flat.
  4. Pat H

    Cable tray supports needed

    I could do that but they don't offer much side to side support. The whole tray could move sidewsrds and collapse. But I could sort that with 2 diagonal supports.
  5. Pat H

    Cable tray supports needed

    I'm looking at fitting some cable trays in a domestic loft. I need them to sit 150mm above the current ceiling joists running across those joists. I'm struggling to find and tray supports that stand up from a wooden joist. Plenty of options to hang trays but that's not practical. Any ideas...
  6. Pat H

    Solution needed!!!!…I used a Contactor instead of an ATS to connect 2 power sources (main and ups) for power redundancy

    Why aren't you feeding power to the Ups and the ups to the server?
  7. Pat H

    Critical load from PV battery

    Thanks. Its a bit more complex than that (of course) I'm adding a manual change over switch to my split rail main consumer unit so I can feed an external 3KW generator to that rail (that will feed the "critcal dist board" as well as the rest of the house lights and sockets. the other consumer...
  8. Pat H

    Critical load from PV battery

    Re UK approval I've not yet found anything that's not industrial plant type size and pricing. Happy to be pointed to a UK approved domestic solution just found any. If I have to go with the unit I listed I'll be using a 63A specd unit at max 22A and typically less than 1/2 that. In a metal...
  9. Pat H

    Critical load from PV battery

    Sorry yes of course it is. Currently the spec is for a Sofar 3K-6K TLM invertor at 6K No critical as in fridge and freezer. So not critical as such (just the term they use for that specific output.) Interesting that they are now advertised on this very site:-)
  10. Pat H

    Critical load from PV battery

    Hi folks. I'm having a PV system installed with a 5KW Amasstore GTX5000 Battery. This comes with a critical load output. I have the spec sheet but its not clear if this output is active all the time or only engaged when the grid power goes down. I'm assuming its live all the time (unless the...
  11. Pat H

    Motorcycle Electrics - indicators on my VTX1300

    You need to order a set of load resistors to install across the feed wires to each indicator lamp.
  12. Pat H

    A friend had a new consumer unit fitted

    I wasn't able to help as really busy but they were having a new kitchen installed. The fitter said they need a new ring main for the kitchen and so needed a new consumer unit. Had a look the other day. No RCD protection as it trips on the old ring main. The guy recons its the supply at fault...
  13. Pat H

    2006 Honda Civic Headlight Switch Buzzing & Headlight bulbs blowing regularly

    Headlights take a lot of power. even 55W bulbs x 2 is 110w at 12V is nearly 10 amps. That's a lot to put through a rotary stalk switch. I'd have expected a relay. However this diagram: Upozorenje o prebacivanju -...
  14. Pat H

    100A DP Isolator Installation Between Meter and CU

    I needed tom upgrade my DNO fuse to 100A so needed to increase my tails to 25mm. Contacted DNO and they agreed to replace tails and increase fuse to 100A I ordered a 100A isolator (in a plastic enclosure) When the DNO arrived I asked if they would fit supplied isolator. They were happy to and...
  15. Pat H

    Am2 safe isolation advice

    If they felt you were unsafe they will have stopped you then ant there. If you completed till the end then there should have been no safety issues.
  16. Pat H

    Close Call for mum with a kite

    Unless it was damp and the kite cord wet whats the conductivity of 50M of nylon cord? Its not that conductive is it? String can be as it tends to hold moisture but thin nylon cord? Its not something I'd test but I'm not sure the danger was that great.
  17. Pat H

    Mains powered smoke and carbon monoxide alarms

    Do you need a CO alarm? on every level? is there an open fire or gas appliance on each level?
  18. Pat H

    Large Benjamin's health & safety

    Why not employ deaf people to do the work? That way they tick their disabilities box as well.
  19. Pat H

    Electrician Jobs Switch for entire lighting circuit?

    How about an overall timer for the lighting circuits so off during the day but automatically on for night (allowing local switching on and off) then an override to allow day use if needed.
  20. Pat H

    LTD Company Directors Salary and CIS

    I do work that gets paid both ways. By invoice it goes into the company account and I get paid from that after deductions. If I'm paid as an "employee" and deductions have already been taken I pay it into the company and take it directly out as is (as deductions already taken) I let the...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top