i have the above panel and have a problem with the system not unsetting and going staight into alarm when entering the premises
System was working fine before it was reset due to losing the engineers code to add new circuits
its an existing circuit Zone 1001 - programmed final with 30 seconds...
So...
A mate just moved into his new house and wants a few extra sockets added for wall mounted TVs etc
No problem you would think as house it fairly modern, I would say less than 10 years old...
Popped round on my way home this evening and looked at the consumer unit , looked okay dual rcd...
I’ve been in my apprenticeship for around 1.5 years now doing electrical engineering, I’ve been put on the ELA course instead of the City and Guilds. Few of the lads at work said I’ve been stitched up because no other companies will accept ELA, just wondering what’s the difference and am I...
Hi there. We have a 4 sets of what are currently battery operated lights. We would like to either connect them all to one power battery source or ideally to a plug to power them. Any advice appreciated
Not sure if this has been announced already, but if it hasn't, here it is.
THE FORUM NOW HAS MORE THAN 1.5 MILLION POSTS!!!!
Threads 126,514
Messages 1,522,317
Members 25,694
Hello all ,
In the garden there is 1.5 3 core armoured cable running from the exterior wall to an outside socket , the power is from a socket inside the house (on the interior of the same wall) I know the sockets are wired in 2.5 but why is the armoured 1.5 ? Thanks
Question for someone... I have a 3P 1.5kw motor gearbox on a 5meter conveyor driven by a 3.7kw omron VFD, Frequency is set at 70/80hz (required for needed speed on this existing drive train) and voltage going out to motor is something crazy like 470v between line and earth, Its way to high I'm...
Getting massively in my way is a brand new, shrink wrapped, 500m drum of NoBurn Enhanced 1.5 2c + e and nearly 2000 7mm red P clips to go with it.
Make me a sensible offer and it's likely to be yours and an absolute bargain buy!
Not working on this circuit but not sure what to do. The circuit appears to only supply an unused FCU which I'd like to disconnect in the CU but as it has nothing to do with the work I'm doing I cannot spend too much time investigating the full circuit.
I have isolated the MCB overnight and...
So was sent to move some sockets today on a big office display anyway I spotted all the display light strips on extension leads made up of a 13amp plug top some had lower fuses others didn't but the plug top where on 1.5 t&e so I've now been asked to do a report on this and other bits so before...
I am replacing a 1.5 internal cable that was run temporarily to give a constant on feed to,my new boiler, as the previous one didn't require this. Unfortunately the only route this could take was from a bedroom ceiling through the floor to the boiler downstairs.
I intend running a 1.5 armoured...
ok.. so any help appreciated..i want to add some Klik lighting management boxes to the end of a circuit to control 10 lights. The circuit up to the ceiling rose I wish to utilise to feed my first klik is wired in conduit using 2.5mm cable. I want to add a two way lighting switch to control the...
Which code would be considered appropriate for a ring circuit protected by a 30A rewireable fuse wired in 4 core 1.5mm2 MICC cable installed to method C. Circuit consists of 12 double sockets serving a large chapel area in a church dating to approx 60 years. I have put a code 2 for...
At a job recently where the previous spark had left the 1.5mm lighting cables within the consumer unit,
with no slack at all., which left the connections to the fuse terminal under strain.
is there an industry standard way of sorting this problem ie adding a short length of cable to the...
Hi All, before we ask the Client to spend any money on a new EPC assessment..do you reckon there is any chance they can get to D if they fit a 1.5 kWp system (nice south-facing roof)?
Hi
I have my mcs inspection in a couple of weeks and have been sorting out the QMS on version mcs1.5 that i have a template for but as i started putting this together about six months ago,I see that there is now a version issue 2 that only has 18 clauses.so when does this actually come in to...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc