16amp

16amp

Recent contents View information Top users
  1. will_505

    3phase 32amp socket swap for 16amp

    Hi there, I've got a 3 phase compressor and a small 8500W single and 3 phase generator. My compressor has a large 32amp plug on it but my generator only has a 16amp socket so my question being can I swap the 32amp plug to a 16amp plug? Sorry if this is a daft question. Thanks guys 🙂
  2. popeyedwazza

    UK Can you have 3 13 amp fcus in series on its own radial 16amp with each supplying single socket

    Hi everyone. Im new here... I need advice on wether it is safe and okay to have 3 × 13amp fcus on its own radial with each having single socket to supply a.... 1st) fcu at 13amp-fridge/freezer 2nd) fcu at 13amp-washer/dryer combo 3rd) fcu at 13amp-Dishwasher They will be protected by 4mm...
  3. C

    no oven for xmas :-( new 16amp oven on onto old 20amp breaker.???

    Hi there My old oven broke just in time for xmas😭😭😭 (murphys law) Ive picked up a new one which is rated at 16amp. The old oven came off an independent circuit. 20amp breaker with 6mm from board to isolator and 6mm to rear of oven. Is this just a case of just hardwiring it in or is it a bigger...
  4. V

    I am allowed to replace the 2.5mm wire from a radial circuit to 4mm and the 16Amp MCB for a 32Amp

    Could you tell me please if I am allowed in England to replace by myself the 2.5mm cable from a radial circuit to 4mm and the 16Amp MCB it has now for a 32Amp?
  5. D

    Two 16amp oven installation

    Hi, I've searched these forums and have found quite a bit of good information, but not specifically to my query. My house is about 9 years old. The kitchen has a dedicated cooker circuit, which has a 32 amp MCB. The cooker circuit only has two single 13 amp sockets on it, and each of these...
  6. A

    Two 16amp ovens on 32amp mcb B supply

    Hi, I am replacing an old double oven with 2 new small ovens. The old oven is wired into a dedicated supply with a switch and the consumer board has a 32amp MCB B breaker. New oven 1 requires a 15 amp fuse and 2790W. link below. https://www.zanussi.co.uk/kitchen/cooking/ovens/oven/zohnx3x1/...
  7. M

    16amp oven installation

    Hello. I have a new oven. I understand completely that I need to get it installed by an electrician and will definitely do so but for my own curiosity I would appreciate some help understanding electrical circuits and what I need. Please forgive if I don't use the right terminology here! My old...
  8. M

    Using pre installed cooker circuit for 13amp or 16amp oven.

    Hi all this is my first post. I am renewing my kitchen and at the moment I have a large cooker I'm changing it to a single oven. At the moment the cooker is on its own dedicated circuit with a 32mcb and 6mm cable going to a 45a cooker switch then going to a 45a cooker outlet plate which the...
  9. T

    32amp generator socket to 16amp plug

    I am looking to buy a generator for my mobile catering unit. Most I can find in my price range have a 32amp 240v single phase socket. My unit is setup to connect to a 16amp plug into the consumer unit with an RCD. My question is can I use a 32amp to 16amp conversion lead rather than having...
  10. D

    Can 2 x 16amp = 32amp Supply?

    Hi, I'm visiting an outdoor event at a camp site which has a 16amp supply. My catering unit draws about 30amps - max. 32amps. Is it possible to get a cable that plugs in to 2 x 16amp supplies that will give me 32 amps? The 16 amp connectors are right next to each other. Any ideas greatly...
  11. D

    16amp radial

    I have installed two rcd sockets in a plant room where I work I done this using 2.5 swa cable on a 16amp rcbo as there sockets will rearly be used the length is 15 m long is this ok
  12. 3

    16amp three phase sockets

    I have been asked to install three "general purpose" 16a three phase sockets. They will be used by different machines including some unknown ones in the future so i guess i need to install it as if they were drawing the full 16amps? What size cable and mcb would i need? ( runs on less than a...
  13. L

    Help with 16amp (i'm not an electrician)

    recently bought a 200amp welder and i need to be able to run it off normal mains socket. problem is it requires a 16 amp fuse i believe. what can i do ? thanks in advance

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top