Hi all! Im having an issue getting an electrician to my place before the holiday. My pool is filled and ready to go. I have ran the grounding bond wire and connected it to 4 spots on the pool. The filter has a bonding plate inside and then to the pump itself. I need to run a new circuit. Just...
I have a 20 amp gfci pool pump breaker that trips only when the pump is off during the night. Pool pump runs fine all day. I turn pump off manually at night by using the manual switch on a Intermatic pool timer. Watch it for 5 minutes and note that breaker remains in on position. Go out in...
I need advice regarding an electronic problem on my Hayward Power-flo Matrix pool pump.
I notice that :
1. Neutral wire from source has become hot and cracked
2. Burn spots are present on the electronic board:
Under resistance R1
On the motor connection
On neutral wire connection
3. Switch...
Hi all
Back in July last year I installed a new pool pump/motor. The problem is it's now making a humming noise and trips the breaker.
I initially thought it was the capacitor, but opened up the back to find there is no capacitor. Didi a little research and thought maybe it was a shaded pole...
Hi everyone
I came across a single phase 230v 2 speed pool pump motor the other ay and became obsessed with how they work and are internally connected , but cant seem to find a diagram/pic of the anywhere. I decided to do my own from what i found on line
My question is have i interpreted the...
Need some help please. Got a brain teaser for my first post. My pool pump motor cratered over 4th of July. It was working fine and started to sound like it had gravel in it. I turned it off at the timer to backwash and the breaker tripped. She was locked up. Since it was 8 years old I took it to...
Installing a small above ground pool with a 1/2HP 120v pool pump. The house is older and has no grounding system that I can tell. Outlets are two prong. I know I need a gfci outlet to plug pump into but will this be safe and work as intended with no grounding system and only a hot and neutral...
Hi,
I hope that someone here might be able to put my mind at rest. I have an engineering mind and a reasonable understanding of electical work, but I'm not confident on this area and want to ensure the safety of my family.
I purchased a bestway splasher pool a few years ago (holds around...
My pool pump (230V 1Ph cap start) US Motor k63cxdfw-5159 ) wasn't working so I started to look for a reason. I found the terminal to the output control relay in the Intermatic program timer/ freeze control was burned off. None of the terminals were insulated and very close to each other and...
I apologize if I double post. It think it went through the first time.
So much OLD information on the web for out dated code it's overwhelming. I watched a near two hour You Tube video on NEC 680 2020 code!
Last year I used a 12 Amp extension cord to my pool pump as a temporary fix. I want...
Good morning all!
I think I have the right amps for a new inground pool pump but I need to ask a pro. I don't want to burn my house down ?
The old hardwired pump I'm removing has worked great for years. Its amps are stated like this, "7.8 - 7.4/14.8." The new pump I want to replace it with has...
New member, DIY homeowner here.
I bought a new in-ground 1HP 120v Harris pool pump (online) and had it installed by my pool maintenance company. A few weeks later it appears blown -- it hums when the power goes on -- but I removed the back and the shaft turns easily so I suspect wiring issues...
I need to run a dedicated line for a pool pump which would be about 140 ft from the outside panel. Pump requires 14-15 amps at 2HP. Should I run a 20 or 30 amp breaker and with what gauge wire? Plan to DIY with some help and would like to use conduit. Any advice is much appreciated!
Hello All,
Am checking a fault on someone elses install which is about 18 months old. Customer says it starts and operates ok then he stops to take a break ( it's a small pool with pumped flow to swim against), then tries to restart and the RCBO goes. So, I know it's hot when it happens but...
Hi All,
New to the forum. Have experience with some control systems but mainly experienced in sensor systems (pressure, temperature), control signals (0-10, 4-20) and data aquisition, dabbling in some automation.
I'd like to connect my pool pump into a control system I'm building. The current...
I accidently removed power supply cables from my pool pump
Advise please on what terminals to connect to. Red, Black , Earth-
Any help greatly appreciated
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc