I have a 5.9kW solar pv array and an 18kWh FoxESS battery with a H1-5.0-E inverter which has been operating for a few months
very satisfactorily. My problem exists with the data that the app gives me. The battery is topped up each night with Octopus Go cheap rate electricity, which runs the...
I have a track light whose power supply failed.
I would like to replace the power supply but am unsure as to what to replace it with and how to connect it to the track.
I do not know the type of track I have.
I could put up to 6 50W 12V halogen bulbs on the track.
How do I determine what type...
Hi,
I have a new wooden shed with dimensions 4.5 meters x 1.8 meters. I would like to have lights and a heater in it to keep decent temperature during winter and work in it - and maybe a small TV ;). I have researched some information and looking at a solar panel, leisure battery setup. I...
I recently installed a 200kva, 33/0.400 KV transformer for a small commercial hostel, so after powering the transformer, we checked all the output of the 3 phase at the secondary side and it was ok but whenever a single air conditioner is powered , then the voltage becomes low. Please guide me...
Hello,
I'm no Electrician, but I think I have a understanding of the basics.
Few years ago We had our Garage supplied with power by and "electrician". This was done by my Wife's family friend, and he never finished it in my eyes.
I've attached a diagram of what's going on...
Greetings
I work for a client who has recently negotiated a bigger supply from the supply authority, the client has agreed with Scottish power to have a larger transformer and feeder cable installed, my part of the works is to upgrade the existing switchgear to accomodate for the new supply...
Hello, everyone!
I'm brand new to this forum. I have a question regarding my laptop. Its input power is 240W @ 19.5 V, and about 12.3 A. Its power supply naturally outputs this amount (nominally), and draws from the socket 100-240V @ 3.5 A (50 - 60 Hz).
When I was working back in Italy (220...
can you use a 5.5mm 2.1mm 12v DC Connector Plug Power Jack replacement as Xmas lights end socket broken off - the voltage through the adaptor is 31v max 6w ?- but no problems with the adaptor which is a Czjutai Power Supply JT‑EL/FC31V6W.
I cannot find a higher voltage replacement power...
All this wind seems to be causing quite a headache for the grid.
not seen it this bad for a long time, if ever.
note, this is only for western power distribution area, I bet the whole country would look like a measles outbreak if there was a map of all areas.
Has anyone installed a Walbox EV Charger with a Power Meter to enable the Power Boost option? It's installed but there doesn't seem to be any way of confirming that the Wallbox is talking to the Power Meter. I spoke to Wallbox and they couldn't help.
Hi,
Hope someone could help with below situation or recommend a good forum to ask about or find information on as I read a lot on the forums and watched many videos but it just got very confusing.
Objective
We acquired 7 sets of led sugar canes, each set has 40 Red leds and is powered by 2 AA...
I have 2 external HDD's I use often. Both Power cables are 12V 2A supplies & input 100-240v 50/60Hz 0.80A. However, 1 of the plugs has broken, I stood on it. The other plug powers either of the HDDs. My question is, if I buy a splitter, will the power supply power both HDDs at the same time if...
Hi All.
I am retrofitting seats into my Subaru Impreza, from a legacy. The new seats are electric and were working fine coming out of the doner car.
There was an existing unused wire under my seats so I connected that to the new seats. Its showing that there is 10v getting to the connection...
Hey everyone, lately I've been trying almost everything to reduce the electrical noise over my Be Quiet Straight Power 11 850W 80+ Platinum PSU which exceeds 2000~ mV or 'onlygodknows' how much it goes up, just right after powering up my pc. How could possibly an premium quality such as Be Quiet...
Please don't all kill me here but,
I replaced 3 lights tested those 3 and all working. Went to do a 4th a restored power and now the rcd trips.
Put everything back to how it was and no power to any outgoing circuits but all circuits have 240v.
No tripping at all unless I put in a plug top...
how to calculate the needed power to light up 6 cool white and 6 white HPL chip like this ?
what is the compatible driver specifics to light up 6 cool white and 6 white HPL chip like this ?
I have a rock slab saw that needs rewiring. The saw's has a 1.5 hp motor as the power source for turning the blade, and I need to add a small 4 RPM motor to run the power feed with a 2 wire toggle switch to control it. It needs to be wired so the saw's main on/off switch turns on both the saw...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc