Currently planning a new rewire for my kitchen and want to get things right first time when it comes to appliances consumptions and circuits.
Unfortunately I don't have the wattage of appliances as some not bought all yet but will go for worst case to be safe.
the oven will be on its own...
Hi, I`m looking for an advice.
I have an electric shower that I`m not using due to boiler changed to combi and added shower over bath feed by a 6mm cable and 40 amps fuse. The cable is quite newish (blue & brown) compared with the rest of the house (red & black).
I want to create a new radial...
I'm doing an design project at college and are onto my cable calcs now and I'm fine with my lighting circuits and the fridge and dishwasher supplys where the load has been stated but I'm confused as what to do about my socket outlets as in the spec there is nothing specified about the socket...
Could you tell me please if I am allowed in England to replace by myself the 2.5mm cable from a radial circuit to 4mm and the 16Amp MCB it has now for a 32Amp?
I'm in the process of renovating a house. As I go through room by room I am removing old plaster and as the cables are exposed at this point I figured I may as well get the wiring updated as I go. The ring main (~6 sockets) is currently fed from 2.5mm T+ E. Eventually I would like to have the...
I have been given this assignment "the drawing below shows the floor plan of a small factory with the electrical symbols. Explain the process of designing the final electrical circuit that supplies all the elements 6 . The total length of the circuit is 25m. Any assumptions you have to make...
Hi.
I have a radial circuit supplying electricity to the garage (part of the house). It's on a 20amp breaker, uses 2.5mm cable. It currently only supplies a single socket. Before anyone asks, its 100% a radial circuit. 6 months ago I had an electrician install a new consumer unit, and the...
Hi all,
After some advice here to settle my mind, is there any regulations to limit the number of sockets on a 20A 2.5mm radial? Reading regulation 433.1 i know it states 50m² floor area, but i can't seem to find anything about the number of sockets? Or is it just the total load that...
So I'm back to work after the bank holiday and I've been asked to install a couple of sockets so they can plug this big beast of a ups system into it.
Currently they have about 5 extension leads all linked to gather supplying it ?
I've never worked on a three phase board before but I will...
Hello all,
Just had an electrician wire in a radial circuit in my house to my loft as I use the space for my home theatre equipment & wanted a dedicated circuit for the equipment as its consists of quite a few power hungry amps & devices.
He has wired the radial in 4.0mm2 twin & earth cable...
Hi,
I’ve been recently working on a living trailer for a friend, when they have the supplies connected (240VAC 16A) they have nuisance tripping on the RCD. I’ve traced through and found an outside waterproof socket to be at fault, short circuit between live and earth. Removed the socket and...
Hi all,
I am installing a Radial A2 circuit which by rule it should have an MCB of 32Amps, but when I reference the table 4D1A using reference method A or B, current are 26 and 32A respectivitly..
So the question is why we go for a 32A mcb and not 25A one?
Thanks
Hi all, I’m new to this forum so please bear with me. I live in a bungalow and would like to repurpose an unused shower cable to supply one new double socket. The radial shower circuit cable is 6mm and protected by a 40A mcb. My plan is to connect the 6mm cable to a length of 2.5mm cable which...
Now chaps,
Will a radial circuit on a 20amp rcbo be enough to power a washing machine, dishwasher, dryer and fridge freezer?
At the moment the radial has a 2 gang to power 2 appliances and a 1 gang to power fridge freezer, possibility of spuring of this circuit to power an extra appliance...
Hi everyone
I am doing level3 design andI have a circuit to design but I have confusion with radia circuit maximum floor area to understand?
I have a socket to feed on the design and floor area according to my knowledge is Length multiply width so in that case it exceeds 75 m square so I am...
Hi All,
I have a very mystifying problem on a very simple circuit.
It is a new radial circuit for a garage power supply, it's wired in 2.5 T&E 16A MCB 30mA RCD. The cable goes directly from the dis board up the wall in trunking to the roof space where it is clipped to the joists before...
Not sure if this is possible but just putting it out there...
Current Situation
Need to tidy up some of the mess in the garage from the previous owner of the house. Wires going all over the place.
Additionally, all of the upstairs lights, the garage light and an external light are all radial...
Hi all, working with a spark today, basically dodgy wiring in kitchen junction boxes everywhere, all ripped out, now all we’re doing is a new 6mm cooker feed and radial socket circuit, basically new 2.5mm radial circuit from CU to one side of kitchen where spark I’m with has decided to put a...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc