Hi, I don't use my cooker point I have a gas cooker, can I replace this cooer swich-sock with a double 13a socket my system is RCD controlled Ciruits your help is appreciated.
Hi,
I am looking to replace the normal light switch (on/off flick button) with this PIR switch (with On / Off / PIR / MIC sensor) as shown in picture E4 and need bit of help in confirming the wiring as this diagram has confused me.
New PIR sensor has only two slots for wire labelled as 'AC'...
HI all. Visited forum many times but first post. Thanks for any help in advance. I'm replacing the 8 (currently) low voltage down lights in my bathroom with 5w 230v ip65 led ones as the old transformers have bitten the dust. My plan was to just replace the switched feed currently running to the...
Hi
We have two alcoves with a downward niche light in each. About 4 years old. Pic attached.
Both operate from one switch. One light is flashing like a strobe when switched on - guess needs replacing?
Appears to be a solid unit rather than containing a bulb that can be replaced.
No obvious way...
As above really, but asking what paper trail is needed in this situation for notification to the FIT provider ( SSE), can a non MCS registered sparks carry out this simple task as its miles away from us, TIA
I am not a electricion but are competetent in doing these jobs .if I change an ordinary wall mounted socket in my French house ,do I have to get it signed off
Tomorrow I’m changing my consumer unit in preparation for my NICEIC assessment on 13th November and have a few queries.
Firstly, current cu only has 4 circuits sockets up & down and lights up & down, so hopefully a pretty straight forward swap.
I can unplug 95% of loads on both ring finals...
Hi,
I am a keen DIYer and eager to learn.
I have just moved into a house that has a solid ring 6 kw electric hob and built in single oven.
I want to replace both and I have bought a Beko Single Oven and a Induction hob.
Currently the old hob is connected to a 13A plug plugged into a socket...
Hi all, I'm a newbie to the forum and I'm replacing a wall mounted extractor fan in the kitchen. The existing fan wasn't working when we bought the house, but it is wired on twin and earth cable and is switched off and on by an isolation switch (no pull cord). I assume that it didn't have a...
hello
I first want to say I am autistic and have difficulties communicating so if any problems arise I am sorry.
I have no experiences with electrical stufff, but my mum was a school caretaker and knows enough to do simple things.
I often leave my bedroom light on all the time, costing loads...
Good evening all,
Looking for a bit of a help, seems a relatively small task (hopefully). My property has a dimmer switch which no longer works, I purchased a replacement today although I'm now not certain that I will be able to use this as the connections are labelled differently from the...
I have a customer with a nobo system 500 orion 512 controller that has burnt out.
I know that these are obsolete, but is there anything I could replace it with to control the nobo panel heaters towel rails etc please.
Hi,
Does anyone know i its possible to replace a set of light switches in a stairway that all control the same lights with a set of PIR switches?
The current rocker switches have L1, L2 and COM but the PIR switch I am looging to replace them with only have L1 and L2.
Thanks
Hi, I need to replace the "8w SMD LED" for a light in my rented apartment but there are 2 issues. firstly, I can't seem to find a replacement and secondly, it looks like it requires some hard wiring.
Saxby Lighting Ltd
Model 46395
Any advice on either of those points? Pictures attached.
Thanks!
Hello
I have replaced three of these switches (single switch) in my home with no issues, but looking for advice on the two gang version.
I have two ceiling lights and two wall lights with a dimmer for each as per below.
There is a live going into COM on each dimmer with a small loop wire...
Hi, my company is in the processing of upgrading lighting from fluorescent to LED. I am having trouble sourcing 1800mm x 600mm recessed panel light fittings. Is there anywhere that still has these sizes as all I can seem to find is the 1200mm x 600mm? How should I replace these units? All...
Hello there,
I apologise in advance if this is a really amateurish question, I am looking for some advice about wall lights and in the absence of yet having found an electrician who can do the job, I am hoping to get some advice from someone on here.
I am due to move into a new house in the...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc