Hello,
We have a project where there are sections where 34.5kVac cables will be laid below 800Vac cables. Conductors are Aluminum.
Any chance anyone knows a standard which states the min. allowable separation distance when cables of different operating voltage levels are laid in the same...
Hi all,
Hoping for a little advice. I work in the Asbestos industry and we manufacture mobile decontamination units we follow the HSE 247 that states all units must comply with BS7671.
We have had a heads up that new regulations may adopt the use of electrical separation (assuming the use of...
hello everyone, I have a little problem. I've got a three phase board, it has the three phase sauna, one phase lighting and sockets connected to it. The problem i am facing right now. This is a comercial unit. So the problem is that the sauna makes the RCD trip every so often. And the board...
Hi all.
I'm a member of a FB group for people trained through a particular training provider. Recently someone posted a query for testing for electrical separation for shaver sockets, and my ex trainer responded with the following method (cut n paste verbatim):
you need to confirm separation...
Hi,
From site to site someone always seems to have a new previously unknown insight towards elv and Lv running together.
I’ve heard :
‘They can run together for 600mm”
“They can cross over and touch”
amongst others.
No one however can ever provide a reg number.
Does anyone here have any...
i have installed some 4inch tray horizontal around a mains room in factory carrying for the moment a couple of 4mm twin earths ,more will be added later, the cctv and data guys have come along and tywrapped their cat 5 cables to this tray ,it maybe just a temp measure as it is very roughly done...
Hi, could some one please explain to me the point at which the feeder stops and becomes a branch on the attached drawing. This is really bugging me and if I had hair it would all be ripped out by now and I am struggling to under stand. Anyone's help would be most appreciated.
Thanks in advance
Hi,
Is anyone can suggest me, what is the separation distance between underground HV cable and Communication cable? An existing communication duct is found across the new HV cable route whilst new trench is dug for HV cable laying. Is there any reference or literature that mention about the...
Hi
Is it agree to put power cable and data cat6 on the same cable tray .One side power cable in trunking other side cat6. it's 15 cm separation between them.what separator should be use?
Thanks for help
Hi, I am relatively new to testing and was just doing some research into it all as some time in the future may take my testing and inspecting exam, I just wanted to confirm this test exactly as i want to make sure I'm understanding it correctly, I know nowadays this part of the test is quite...
Hi,
I have noticed the following item in a new construction site. Could anyone can give me further suggestion, please.
1. What is the minimum separation distance between LV underground cable and water pipes (Cold water)? This is for new underground cable lying. Water pipe is to run parallel...
Hi all.
It seems there has been quite some different opinions in my classroom as to who should really change the earth cable in the incoming position where the 100A fuse is, in domestic installations.
Can any qualified electrician, change the earth cable at the DNO side? Say for example on an...
Hi,
I had an interesting conversation at work today which might cause a few problems.
I am fitting 4 pole MCBs to protect the 1.5mm 3 phase feed to some motors (There is no neutral).
The 4th pole is part of the control circuit.
My idea is that if the MCB trips, it will delatch the control...
I have some electrical cables in the garage that cross a gas pipe at 90 deg.
Am I right in thinking that there should be 25mm separation or the gas pipe wrapped in insulation / PVC? Would it be ok to acheve this by slipping a PVC waste pipe around the gas pipe or is there something available...
Hello,
I'm doing a periodic inspection and am unsure weather to fault this,
I have a generator which is the source of my supply, this then feeds two main distribution panels out of the main switch. So there is two 3 phase supply cables out of one MCCB. Does 314.4 come into play or does it...
Hi All,
My assessor suggested there is no need for frame bonding if a TL inverter has electrical separation between DC and AC. This is news to me and wonder if he is getting confused RCD requirements, but he is adamant.
Anybody heard this? Is everybody bonding TL’s and including earth...
It is planned to install a central 24V SELV supply in a domestic residence, e.g. to power LEDs.
According to my reading, BS 7671:2008 chapter 414.4.1 (ii) requirements for protective separation between a SELV and 230V circuits offer the following options
a) double insulation -or-
b) reinforced...
Hi gang
im currently testing a theatr in north wales.
ive come across a 1:1 isolating transformer feeding 32 bench sockets, it was installed in 1976. its in an audio/visual repair shop where they used to repair old tvs etc.
all the sockets have an earth
L-N measures 230v
N-E measures 110v
N-L...
Have got a building to wire with data and coax with the usual power. Am going to put in a trunking system. the question is can i run my data for IT sockets in the same compartment as tv coax cable??
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc