I have "grid failure, check fuse, 801" on my sunny boy inverter. I want to switch it all off and switch it back on again but cannot remember in which order I do this. There is a red knob to the left "solo pv system" and a black knob to the right "pv array". Which knob do I turn off first...
Hi there, I have noticed that my solar system has not shown any reading since December 18th. I have tried turning the system off and on but still not working.
The system is a sma sunny boy 2000hf with 8 x hyundai 250w panels.
The sunny boy is about 6 years old and has never given me a problem...
Has anyone ever had code 6403 on a sunny boy 3680 inverter. The inverter has been replaced 3 times on advice from SMA as they are saying it's an internal component failure, surely not on 4 inverters though.
The original install was done by myself in February and all was fine until a few weeks...
I have a new in the box sma sunny boy 4000tl with
a sunnybeam.
When i do get installs i use solar edge
so if your looking for a sma sunny boy 4000tl
If your intrested in buying it i want 900 for them both
Saves you about £250 - £280
Willing to drop off if your within a hour n half from me
Afternoon all,
Just thought i would share my afternoon with you all.
so i have 2 x SMA Sunnyboy 1200 inveters both situated outside next to each other(IP rated of course), when i noticed an earth fault today.
Following the manual, i tested the string, + to PE and - to PE, both 0 Volts
So went...
VMan
Thread
earth
electricians' talk
fault
inverter
somewhere
sunnysunnyboy
water
Hi..!
I was wondering if anyone on here has come across this before..... I Just put in a sunny boy 1200 today and it was working fine green led on all day for only 6 hrs exactly ,,says it on the lid display and then it turned off at exactly 6:01pm with the green led blinking saying grid...
I am about to replace my 3Kw Immersion Heater with a 1.5Kw. Please see the attached PDF
I intend to control it with the multi function relay in the Sunny Boy turning on at 1800w. The default setting for self consumption is 1500w
The other settings I am considering altering are the default 30mins...
Orty
Thread
contactor
electricians' talk
function
immersion
multi
relay
sunnysunnyboy
ok, so here's my first post.
Just got Sunny Explorer set up via Bluetooth from my laptop. Connecting to a Sunny Boy 3800. I'm trying to check if it's been set to UK G83 (From searching on here 5 and 8 inside the inverter) without opening the inverter. I've powered down and G83 does not appear...
We are having to rush a decision on which of two quotes to give the go ahead to - both who can fit us in for install by end of november. Unfortunately our preferred installer (most reputable) couldn't fit us in.
The chap we've so far given our deposit to (with a 14 day cool -off available)...
Inverter goes through start up sequence green light flashing 1 per sec "waiting"
But does not start to feed
I have 156V DC coming in and 122V AC on the grid side
Any advice would be greatly appreciated
Out of 10 sales pitches, only 3 companies passed the BS test. My prefered option, salesman strongly recommended Sunny Boy Transformerless Inverter, now the quote has arrived stating SB3000HF (for a 3.5kwp Sanyo HIT panel array). Is this transformerless? I was expecting to see a TL model. I...
Hi, Im trying to match an inverter to 9 Suntech 190 24AD+ Mono panels. It wont allow 9 in one string but will allow 2 strings of 4.
I'm trying to get it to show 1 string of 4 and 1 string of 5, is this possibe or am I not using the software properly?
TIA
Woko
woko
Thread
electricians' talk
panels
software
string
strings
sunnysunnyboy
using
voltage
Hi
I have installed our first PV system, which we are using to get MCS accredited with. Its a small 5 panel system as roof space is quite small. The panels are 195w each.
The Voc for the panels @ STC is 45.21V and Isc @ STC 5.56A.
Our measured Voc on the day of commissioning was 211V. I thought...
bigsparks
Thread
again
array
electrical work
electricians' talk
inverter
not working
sunnysunnyboy
working
Hi All
Still very new to this game and was wondering if Anyone knows if you have to separately Bond the inverter, particularly the sunny boy 3300. I See It has a separate terminal lug for bonding, But have never seen any one use it.
Any Help would be greatly appreciated as I have my Inspection...
Has anyone had any issues with Sunny Boy inverters before? We've had one playing up on us for the last couple of weeks. On a couple of occassions now, we have had "Disturbance" come up on the inverter. I haven't been there to witness it so can't give any more information. The inverter has...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc