table saw

  1. R

    Table Saw 3Ph conversion to Single Phase

    Hello Everyone -- So, I am looking to buy a used 5HP 3PH 208 V 10 inch Table saw --- (Motor Plate Data in Image) I am a DIY'er and in this case I would not attempt to do a 3PH to Single Phase conversion myself -- (I have looked at many videos and read several articles about how to do...
  2. B

    Table Saw trips RCBO

    I have a ring cct (2.5mm ) in my cabin which is protected by a 20amp RCBO. This has been in existence for over 3 years with no issues. I recently bought a table saw and when turned on, on its own all is OK. However the other day I had a heater and a dust extractor on, then turned on the table...
  3. D

    Hoping to identify the wiring on this 240v Table Saw motor

    Hi Experts, I was given a Ryobi 240v Table Saw which I think came from South Africa. The motor was disconnected when I checked but I would just like to connect up the motor to see if it works. There are four wires to the motor, two black, one grey and one blue. I don't want to blow it up...
  4. P

    Table saw motor wiring

    Hello people. My old man has a table saw and water has got in the switch, he decided to remove it ready for me to replace and due to poor memory can't remember how it was wired up. I've not had much experience with motors etc but from what I can work out it's wired as follows: I haven't...
    • polaroid
    • Thread
    • motor table table saw wiring
    • Replies: 25
    • Forum: UK Electrical Forum
  5. S

    Table saw switch wiring 220v

    Hi All Need help wiring a 220v Table saw switch. I've tried all different configurations, some combos it comes on but got to hold the button in. I've attached a few photos of the switch and wires. The blk and wht wires on the left come from the power cord and the two on the right come from the...
  6. Andy5678

    Table saw switch

    Looking to replace a table saw switch. The saw has a slow start motor, so the usual retrofit start stop switches won’t work. Anyone ever replaced one/recommend a retrofit switch?
  7. A

    How to rewire a table saw

    Hi guys The power cable on my table saw attached to the motor came off when I changed blade to 45 degrees. Turned saw upside down and the power cable was hanging loose, the only wire coming out the motor is a red live cable, how can I reattach the power cable when it has live and neutral wires...
  8. S

    240v 1ph 1600W Table saw motor wiring question

    Hello everyone, This is my first post, so please bear with me. I am trying to work out how the motor to my table saw is wired. I bought it second hand and I think the previous owner has messed with it. One of the brush holders had been forced in and was touching the commutator. I am wondering...
  9. M

    Fault table saw Advice needed

    In the Workshop we have table saw which sometimes doesn't start just hums and you need to start the with a bit of wood, I have only just started with them and they asked if it could be fixed for me its a capacitor problem but i don't want to say order a new capacitor and it will it work in-case...
    • Maestro
    • Thread
    • advice capacitor fault ideas needed start table table saw
    • Replies: 3
    • Forum: UK Electrical Forum
  10. G

    AC table saw motor only seeing 90V across the inputs?

    I bought an old Craftsman table saw (circa 1982) a couple months back and today the motor stopped turning, instead it started just sitting there making an electrical buzz. I've got it apart and all the connections and stuff looked good, so I broke out the multimeter and measured the input...
    • gct
    • Thread
    • across aus motor table table saw
    • Replies: 8
    • Forum: Australia

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Back
Top