Fuse box installed for £150 what!!!

[james the spark]

A medium sized electrical company near me is advertising a fuse box swap and testing for 150 its not surprising people constantly try and press you to try and get the job done cheaper when people are advertising that.

 

[SPARTYKUS]

...with two MCBS and two circuits, all bonding already in place in a one bed flat with one socket in each room. and still too cheap

 

[trev]

I think that company is a subsidiary of one that advertises showers for £90 in the same area. No names but they are on the COAST and they fit SHOWERS (Bet you can't figure that out hehe)

Call them out and they give you some guff about your water pressure being too low so they have to fit a special one.

 

[vernam616]

Taking into account that the bonding is up to scratch, that is exactly what i charge for a board change

Lets face it, it really isnt hard graft is it? sat on arse for 30-45 mins

Maybe i need to alter my prices !

 

[telectrix]

you're far too cheap at £150. what about tracing unmarked circuits. identifying what points and how many on each cct. , testing, filling in EIC time. what else can you do in a day after that?

 

[vernam616]

I charge at £12 per hour for tracing unmarked circuits and faults

Arrive at job 8am, done and cleaned up by 9am, testing till 12pm, onto the next job, simples

I have a image in my head of everyone being the typical tradesman, tea drinking and paper reading, come on lets be honest how long does it take to change a DB and test the install?

Am i the only one who has the "Graft" idea?

And after all the age old saying go's "Stack em high, sell em cheap", the referrals i get from customers who were pleased with the work i carried out and the price is excellent, TBF i dont have a lot of overheads and im not greedy just pleased that i actually have some work

EDIT: and for anyone thinking " i bet the DB's are a mess "

 

[telectrix]

so, even at half a day, take out best part of £100 for the CU, you only got 50 odd quid for wages, van costs, insurance, tax and NI, etc. etc.

 

[vernam616]

£100 for a DB !

You need to start shopping somewhere else, i get a Wylex 10 way dual split with MCBs for £45

£150 is the bare minimum price like i stated, all the bonding is up to scratch, tails ok etc...

 

[diditrain]

You should advertise yourself as a trainer, showing people how to do them as neat as yours if you can do that in 45 mins.

 

[Deleted member 26818]

£100 for a DB !

You need to start shopping somewhere else, i get a Wylex 10 way dual split with MCBs for £45

£150 is the bare minimum price like i stated, all the bonding is up to scratch, tails ok etc...

How much was the Crabtree in the picture?

 

[cjp1]

£100 for a DB !

You need to start shopping somewhere else, i get a Wylex 10 way dual split with MCBs for £45

£150 is the bare minimum price like i stated, all the bonding is up to scratch, tails ok etc...

£45 is a good price for a wylex 10 way I am paying about £75 - £80 .

 

[Guest112]

i changed a tp boiler house db other day, traced two unknown circuits tested and completed in a few hours, it depends on the job

 

[Deleted member 26818]

Yes it does depend on the job.
Personally, I would charge a day rate + materials, as I would not be able to guarantee how long the job would take, or whether I'd be able to go on to another job that day when I'd finished.
I would also like to include any time taken in assessing the job, and obtaining materials.
Calling in somewhere on the way back from a job, to replace a light fitting or a socket-outlet would be an hourly rate.

 

[topquark]

I charge at £12 per hour for tracing unmarked circuits and faults

Arrive at job 8am, done and cleaned up by 9am, testing till 12pm, onto the next job, simples

I have a image in my head of everyone being the typical tradesman, tea drinking and paper reading, come on lets be honest how long does it take to change a DB and test the install?

Am i the only one who has the "Graft" idea?

And after all the age old saying go's "Stack em high, sell em cheap", the referrals i get from customers who were pleased with the work i carried out and the price is excellent, TBF i dont have a lot of overheads and im not greedy just pleased that i actually have some work

EDIT: and for anyone thinking " i bet the DB's are a mess "

View attachment 8475

Nice and neat, that's what I like to see!

 

[topquark]

Has to be day rate plus parts, no point in doing the job for just wages!