My alarm panel is going into alarm when entering the premises

[Cutepaul]

hi i have a Honeywell Galaxy 2-20-V15 version 1.5 security system and was working fine but the engineers code was lost so as i needed to add more circuits,i defaulted the panel back to factory settings and now have an enginers code . I have reprogrammed the panel and included new circuits and everything appeared to be fine, but the problem is the system is setting fine but on unsetting it immediatly goes into alarm
This is curcuit 1001 programmed ,final and timed each way 30 seconds/entry and exit
I cannot find anything in the programming to explain the problem but the log indicates code - ENT T/0 can any one advise please ?
regards Paul

 

[mainline]

hi i have a Honeywell Galaxy 2-20-V15 version 1.5 security system and was working fine but the engineers code was lost so as i needed to add more circuits,i defaulted the panel back to factory settings and now have an enginers code . I have reprogrammed the panel and included new circuits and everything appeared to be fine, but the problem is the system is setting fine but on unsetting it immediatly goes into alarm
This is curcuit 1001 programmed ,final and timed each way 30 seconds/entry and exit
I cannot find anything in the programming to explain the problem but the log indicates code - ENT T/0 can any one advise please ?
regards Paul

I’m not familiar with the panel but it seems to be that the entry is programmed to 0 time hence the alarm straight away.

Most alarms that i have seen just have an entry exit time and not have separate ones.

Do you get a beeping when you set the alarm for exit.

 

[Pauly24]

I’m not familiar with the panel but it seems to be that the entry is programmed to 0 time hence the alarm straight away.

Most alarms that i have seen just have an entry exit time and not have separate ones.

Do you get a beeping when you set the alarm for exit.

yes the alarm is programmed 30 seconds entry and 30 seconds exit yes it does beep and sets fine

 

[snowhead]

Is there a detector on another zone / circuit that also is covering the exit route?
Maybe try eliminating each detector 1 at a time then trying the final exit each time.

 

[mainline]

but the problem is the system is setting fine but on unsetting it immediatly goes into alarm

Are you saying that on entry it beeps giving entry delay but goes off when putting the code in to unset ?

Or does it set off the alarm as soon as you enter the entry zone ?

 

[Pauly24]

Are you saying that on entry it beeps giving entry delay but goes off when putting the code in to unset ?

Or does it set off the alarm as soon as you enter the entry zone ?

hi yes it does set off the alarm soon as i enter the entry zone

 

[Pauly24]

Is there a detector on another zone / circuit that also is covering the exit route?
Maybe try eliminating each detector 1 at a time then trying the final exit each time.

no other zone/circuit covering exit route. it just goes off immediately when entering entry zone

 

[mainline]

hi yes it does set off the alarm soon as i enter the entry zone

Try changing the entry timer to its maximum.

 

[snowhead]

ENT T/O, is Entry Timeout,, suggesting whatever you've set for Entry delay is not being used.

 

[Pauly24]

Try changing the entry timer to its maximum.

Hi tried that too mate no change

 

[Pauly24]

ENT T/O, is Entry Timeout,, suggesting whatever you've set for Entry delay is not being used.

Yes mate tried all the suggestions you've all tried to help and nothing

 

[mainline]

Yes mate tried all the suggestions you've all tried to help and nothing

Can you change it to another zone or link the exit entry out and see if it still activates

 

[Pauly24]

Can you change it to another zone or link the exit entry out and see if it still activates

Tried that too I've got two of these things unless it's 2 faulty panels I'm really puzzled

 

[newfutile]

Tried that too I've got two of these things unless it's 2 faulty panels I'm really puzzled

Make sure the zone is set to entry exit,you might have it set to Immediate,on some panels it might be only 1 zone can be entry exit,also you may be walking though another immediate zone without it set to walkthough

 

[mainline]

Tried that too I've got two of these things unless it's 2 faulty panels I'm really puzzled

You could link out all the zones apart from the one your using for exit entry that would eliminate the others.
Also is your exit entry a pir or contact ?
Is it programmed correctly for the type ? no resistor etc ?