Measuring current using a Shunt Resistor & an Oscilloscope | on ElectriciansForums
Guest viewing is limited

Measuring current using a Shunt Resistor & an Oscilloscope

Post new thread

Discuss Measuring current using a Shunt Resistor & an Oscilloscope in the UK Electrical Forum area at ElectriciansForums.net

F

FernandoDAS

-
Joined
Jun 20, 2019
Messages
8
Reaction score
1
Location
Mexico
Hi people, I'm new using forums for this kind of purposes, so please forgive me if I can't explain myself well, also if this is the wrong sub-forum please tell me ¡.

I have to measure the output current & voltage of a High Frecuency, High Voltage transformer, I can measure the Output Voltage using a High Voltage Probe and my Handheld Oscilloscope, but I still have to deal with the current, I want to use a Homemade Shunt Resistor (0.1ohms) and my Oscilloscope, but before doing it I tried by measuring that voltage with my Fluke Multimeter, I was increasing the input voltage & It was working well but at some point my Multimeter Screen started to fade & show random numbers, What happened? The voltage on the Shunt wasn't that high (around 2.5 volts) when it started to fail, it still works. I don't want to damage my Oscilloscope, so I need to now what causes that issue.

Here is my circuit diagram if you wan't to know the way I'm measuring.

Considerations:
-I know my multimeter doesn't measure at those frequencies, but the error is constant so I can just adjust it.
-I know my oscilloscope does work at those frequencies.
-I have no idea of the value of the output current & voltage, also by measuring another transformer the values are not consistent.
 

Attachments

  • [ElectriciansForums.net] Measuring current using a Shunt Resistor & an Oscilloscope
    Circuit.png
    42.4 KB · Views: 55
Sort by date Sort by votes
One needs to know more about V1 eg: waveform?, output impedance as a function of frequency - what is its Thevenin 'equivalent circuit'?

Similarly, one needs to know more about the transformer - what is its 'equivalent circuit'?

The Fluke multimeter I think is likely to be an unsuitable instrument for your measurements.

The secondary current you measure depends on the source of emf 'looking left into the secondary and its waveform', the impedance looking left into the secondary and the impedance of the load - plus the impedances and frequency & waveform characteristics of your instruments.

Need some more detail from you.
 
Last edited:
Upvote 0 Downvote
Your measurement setup with the oscilloscope looks OK but safety first, the resistors suggest you have a high-voltage, high-current supply and if you're not secure with measurement principles I wonder if you have the expertise to be safe around the supply.

What is the output current and voltage and how are you protected from it?
 
Upvote 0 Downvote
Hmm, meter display going blank sounds a bit spooky and not obviously related to the measurement. Probably just coincidence.
 
Upvote 0 Downvote
Wilko said:
Hi - I’m back with the frequency being out of the meter’s range. Not sure what the point of measuring something that you know will be wrong?
Click to expand...
Hi, sorry it took me ages to reply but I'm kinda busy at work.
You're right, but I wanted to know if the error was somehow constant, & it was (kinda), I don't have access to any other meter so I'm stuck with it.
Here's the relation between the real output & what the meter shows.
 

Attachments

  • [ElectriciansForums.net] Measuring current using a Shunt Resistor & an Oscilloscope
    Voltage.png
    8.6 KB · Views: 27
Upvote 0 Downvote
marconi said:
One needs to know more about V1 eg: waveform?, output impedance as a function of frequency - what is its Thevenin 'equivalent circuit'?

Similarly, one needs to know more about the transformer - what is its 'equivalent circuit'?

The Fluke multimeter I think is likely to be an unsuitable instrument for your measurements.

The secondary current you measure depends on the source of emf 'looking left into the secondary and its waveform', the impedance looking left into the secondary and the impedance of the load - plus the impedances and frequency & waveform characteristics of your instruments.

Need some more detail from you.
Click to expand...

Hi, I know that should provide that kind of data, but sadly I can't show them, what I can show is this:
The input's waveform looks like a square (I'm attaching a pic & yes, where I'm working I only have access to Paint :l).
I still need to do the Thevenin Analysis, It's not that hard but they want me to focus on something else.
My instruments.... I'm stuck with them, I already measured the error, the results are shown in a reply above.
My output waveform looks like a M, I'm also attaching a pic showing it.
Thank you very much, you seem to know a lot.
 

Attachments

  • [ElectriciansForums.net] Measuring current using a Shunt Resistor & an Oscilloscope
    wave 2.png
    6.5 KB · Views: 24
  • [ElectriciansForums.net] Measuring current using a Shunt Resistor & an Oscilloscope
    Wave.png
    6.4 KB · Views: 21
Last edited:
Upvote 0 Downvote
Shoei said:
Your measurement setup with the oscilloscope looks OK but safety first, the resistors suggest you have a high-voltage, high-current supply and if you're not secure with measurement principles I wonder if you have the expertise to be safe around the supply.

What is the output current and voltage and how are you protected from it?
Click to expand...

Hi, & thank you for replying <3.
I haven't had a proper training on that (if there's any), I have no idea about the output voltage & current (actually that's the reason I'm trying to measure it), but the voltage is around the 3.8KV.
About security.... there's none, we don't have security equipment.

Thank you very much.
 
Upvote 0 Downvote
Re #8. The two waveforms tell you a lot. The equal mark:space ratio of the square wave means it contains only the fundamental sinusoid (20kHz) and odd harmonics of it ie: 60kHz, 100kHz, 140kHz,....

[ElectriciansForums.net] Measuring current using a Shunt Resistor & an Oscilloscope


The waveform of the output voltage/current shows it is mainly comprised of the fundamental (20kHz) and third harmonic (60kHz).

[ElectriciansForums.net] Measuring current using a Shunt Resistor & an Oscilloscope


Is your measurement question:

a. 'what is the effective root mean square(rms) value of this second waveform?' or

b. 'what is the amplitude of each component (fundamental, third, fifth, etcetera)? of this second waveform?'
 
Upvote 0 Downvote

Reply to Measuring current using a Shunt Resistor & an Oscilloscope in the UK Electrical Forum area at ElectriciansForums.net

Similar threads

Mixtel
  • Question
Confused - Telaris 0100 plus
Good point James. It would have been nice if the manual had mentioned which of the leads were being used for what though. It simply shows the LNE...
Replies
7
Views
573
Mixtel
Mixtel
J
  • Question
Metrel Earth Electrode test - current injector clamp and measure clamp - can i use on domestics TTs?
I don't think it will work with only one stake unless some meters have different operating parameters. It doesn't necessarily have to be a stake...
Replies
3
Views
1K
westward10
westward10

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top