Ethernet woes… hmmm what to do! | on ElectriciansForums

Discuss Ethernet woes… hmmm what to do! in the Security Alarms, Door Entry and CCTV (Public) area at ElectriciansForums.net

Joined
Apr 26, 2018
Messages
14
Reaction score
5
Location
london
Running an Ethernet cable to my outdoor studio. I did this successfully before using cat 5 but cable severed. Run a new cable cat 6e. This cable is terminated at two Ethernet sockets one in the house the other in the studio.
No signal, tested the connections using an Ethernet tester, the one with eight lights and a ground. No lights. Thought I pulled the cable too hard, bought another cable also cat 6e, tested that withe same sockets, no lights again.
Treble checked my wires are firmly in place and correctly colour coded, identical both ends. No lights at all. Tested the tester on a spare Ethernet cable, this works.

Completely flummoxed now.

Do I have the wrong sockets? Are cat 5 and cat 6 cables incompatible?

can anyone help please?

Z
 
Can you post a picture of the termination?
 
Question, are all Ethernet sockets the same wiring standard, I know there are two standards for wire colors, but if one has two random ethernet sockets wires so the cable colors are identically connected at both ends, would this mean that any Ethernet socket would work with any other?

Than you all
Z
 
I wonder if you've used the tool the wrong way round? Something is definitely wrong.
 
Temporarily remove the wires from one of the sockets. Cut a short length of your network cable and punch it down exactly as.you did before. Use a multimeter to do a continuity test between the bare ends of the wires and the terminals on the socket.
 
@DPG's test is valid but you might be able to go one further, if you have a multimeter or continuity tester, and confirm whether the IDC connections to your cable runs are making contact as they are. Gently, without pulling too much on the wire, strip the last few mm of insulation from some of those overhanging ends. Then test for continuity between the stripped end and the visible part of the contact fork in the punchdown terminal slot.

If there is continuity between wire and terminal, then either there is no continuity along the cable or the modules are faulty and lacking continuity between terminal and socket contact. You could put a jumper cable between two sockets and test to the forks. If no continuity between the ends, check for continuity along the drain wires e.g. by linking the two at one end and testing between then at the other.

If you have no multimeter, try using a short length of cable to interconnect two sockets and then test between them with the network cable tester.
 

Reply to Ethernet woes… hmmm what to do! in the Security Alarms, Door Entry and CCTV (Public) area at ElectriciansForums.net

News and Offers from Sponsors

  • Article
Join us at electronica 2024 in Munich! Since 1964, electronica has been the premier event for technology enthusiasts and industry professionals...
    • Like
Replies
0
Views
187
  • Sticky
  • Article
Good to know thanks, one can never have enough places to source parts from!
Replies
4
Views
577
  • Article
OFFICIAL SPONSORS These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then...
Replies
0
Views
534

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top