Consumer unit relocation | on ElectriciansForums

UK Consumer unit relocation

Post new thread

Discuss Consumer unit relocation in the UK Electrical Forum area at ElectriciansForums.net

R

Riddler

Joined
Jun 27, 2020
Messages
5
Reaction score
1
Location
West Sussex
Sorry, I know this has probably been covered, but I'm struggling to find a recent and specific answer.

Old 1930's bungalow. Really old CU tucked in the corner of the old converted garage, slightly behind a wall, so barely accessible now. Definitely needs moving, but want to move it toward the main building as we're doing a complete rewire inside.
Don't want to pay the DNO ÂŁ2.5k they've quoted to move the incoming, so want to move just the board away from the meter and CO fuse.

I've pictured an isolator that our supplier fitted when we moved in.
Now, am I right in thinking this isn't enough to allow me to move the board. I need to add a fused isolator after this one?
Or, is this isolator enough, and I can run separate cables from here, to where I want the new board to be? Or even connect it to an SWA cable to run it round.

I'm pretty sure I know the answer, but the chap that fitted the isolator gave me a different one, so wanted to make sure before I make a horlicks of it and do something stupid

[ElectriciansForums.net] Consumer unit relocation
 
How far is the board move ?
Would the run from meter to new Cu be through walls etc ?

If the tails are going to be over 2mtrs (most dnos allow 3mtrs) then the best way is a \MFCU and SWA.
 
Last edited:
Sorry, completely missed that info off. Yeah it's definitely more than 3mtrs. The board is at the furthest forward point of the old garage/front room, and want it to be closer to the main building. So in a straight line (which would pass outside, it's maybe 4mtrs. But as a cable run, possibly 10, either through the house, or run it back outside and round the building

And what's an MDCU sorry?
 
Riddler said:
but want to move it toward the main building as we're doing a complete rewire inside.
Click to expand...
I hope you mean that you have an electrician who will be carrying out the rewire?
Riddler said:
Now, am I right in thinking this isn't enough to allow me to move the board. I need to add a fused isolator after this one?
Or, is this isolator enough, and I can run separate cables from here, to where I want the new board to be?
Click to expand...
It is ok for the short tails that you have, but a switched fuse is required for the distances you have in mind.
Riddler said:
Riddler said:
Or even connect it to an SWA cable to run it round.
Click to expand...
Click to expand...
There's no "or even". If you want to extend the main supply any distance through the house then they must be either RCD-protected at the source (you really dont want to do that) or provided in the correct cable which means SWA. So, SWA is your option, and it will be a chunky one. Your electrician is the person who will need to spec the cable, the fuse size and several other things.
 
Riddler said:
Sorry, completely missed that info off. Yeah it's definitely more than 3mtrs. The board is at the furthest forward point of the old garage/front room, and want it to be closer to the main building. So in a straight line (which would pass outside, it's maybe 4mtrs. But as a cable run, possibly 10, either through the house, or run it back outside and round the building

And what's an MDCU sorry?
Click to expand...
A mains fused connection unit
 
Taylortwocities said:
There's no "or even". If you want to extend the main supply any distance through the house then they must be either RCD-protected at the source (you really dont want to do that) or provided in the correct cable which means SWA. So, SWA is your option, and it will be a chunky one. Your electrician is the person who will need to spec the cable, the fuse size and several other things.
Click to expand...
Earthed Metallic conduit is one other choice.
not normally a preferred one as it is more expensive but it is often an option.

p.s. it may well be 32mm or even 40mm diameter conduit depending on what you are pulling through.

I really think you should discuss in detail with your electrician what the options are and how it will look / what the costs are.
 
Exactly what I was expecting. The guy who fitted the isolator for the supplier said it was sufficient to now have a long run to a new board, so that threw me. And I know there's a few advocates on here saying it's fine. But better safe etc
Fair to say, we'll have a fused mains switch fitted after that isolator then, and run swa to the where the new board will be :thumbsup:

Taylortwocities said:
either RCD-protected at the source (you really dont want to do that) or provided in the correct cable which means SWA.
Click to expand...
Btw, what's the aversion to using an RCD, like one of the FuseBox mains switches?

Appreciate the info and advice guys
 
Riddler said:
Btw, what's the aversion to using an RCD,
Click to expand...
Because it is a single point of failure if you have it at the supply input point. One little earth leakage, on any circuit, and you lose power to EVERYTHING.
SWA does not require RCD-protection.
In your new consumer unit, we hope that you are going for RCBOs on each individual circuit?
 
Riddler said:
Fair to say, we'll have a fused mains switch fitted after that isolator then, and run swa to the where the new board will be :thumbsup:
Click to expand...
I would install the MFS in place of the isolator that's there.
 
Riddler said:
Is there an issue with fitting it after the isolator? I appreciate it looks odd and untidy, but just means the electrician can do it rather than calling our supplier
Click to expand...
Not really an issue but as you said looks untidy and more joints to go wrong.

A lot of electricians call the tooth fairy.
 

Reply to Consumer unit relocation in the UK Electrical Forum area at ElectriciansForums.net

News and Offers from Sponsors

PCBWay
  • Article
Meet PCBWay at electronica A1.163
Join us at electronica 2024 in Munich! Since 1964, electronica has been the premier event for technology enthusiasts and industry professionals...
    • Like
Replies
0
Views
265
PCBWay
PCBWay
Electrical2go
  • Sticky
  • Article
📢 Best Sellers Catalogue Now Available! 📢
Good to know thanks, one can never have enough places to source parts from!
Replies
4
Views
756
Bob Labla
B
Dan
  • Article
The Official Sponsors of ElectriciansForums - There are currently 8
OFFICIAL SPONSORS These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then...
Replies
0
Views
740
Dan
Dan

Similar threads

K
New circuits into plastic consumer unit
Yes Napit
Replies
4
Views
500
Km1777
K
A
EV consumer unit tails
This was posted this week, on topic ....... https://niceic.com/newsletter/omission-of-overload-protection/?dm_i=7G1W,7GCE,K4L2A,WHET,1
Replies
8
Views
694
DefyG
D

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top