Table in middle of room

Strima

-

Arms

V.Nearly Esteemed

Joined

Mar 14, 2012

Messages

5,112

Reaction score

6,603

Location

St Neots

• Sep 29, 2012

• #2

Any chance of going through the floor or have they already put the expensive solid oak flooring down, I know bit of a stupid question but have to ask.

 

Upvote 0 Downvote

OP

A

Ashley Williams

-

Joined

Dec 9, 2008

Messages

99

Reaction score

4

Location

Oswestry

• Sep 29, 2012

• #3

Floor has just been tilled! So thats a no go!

 

Upvote 0 Downvote

S

Swicade

• Sep 29, 2012

• #4

2" dairy pipe from ceiling to floor just past one corner of the table securely fixed either end feeding some floor sockets (with the wee flappy covers)....add some lights near the top.....can then be a dual purpose unit,supply pipe for sockets/lights then for those nights when there's nothing on TV you move the table aside and viola you go a dancing pole...


Under the floor before tiles were fitted would've been the ideal route, hanging anything from ceiling to table without some sort of lighting arrangement involved may look odd

 

Upvote 0 Downvote

OP

A

Ashley Williams

-

Joined

Dec 9, 2008

Messages

99

Reaction score

4

Location

Oswestry

• Sep 29, 2012

• #5

Its a commercial environment its a folding table in a laundry where they want a computer to book orders out! Was thinking some sort of large chrome pole to be able to run network cable's down aswell!

 

Upvote 0 Downvote

snowhead

-

Mentor

Arms

V.Nearly Esteemed

Joined

Jan 4, 2012

Messages

5,745

Reaction score

6,138

Location

Mildlands

• Sep 29, 2012

• #6

Is the table fixed to the floor, if not you can't use a tube unless it's self supporting i.e. fixed to the floor at the side of the table.

Roof is only 6ft above, what's the room for, Teddy Bear picnics?

Edited after later post.

As it's a laundry and not a fixed table, Unistrut with sockets fixed to it

 

Upvote 0 Downvote

OP

A

Ashley Williams

-

Joined

Dec 9, 2008

Messages

99

Reaction score

4

Location

Oswestry

• Sep 29, 2012

• #7

Roof is 6ft above surface of the table! Roof is about 9ft off the floor table is bolted to the floor was thinking of fixing it to table and beam in roof!

 

Upvote 0 Downvote

S

Swicade

• Sep 29, 2012

• #8

I'd use 2" stainless steel dairy tube! then run my cables in that! mount a stainless steel plate for sockets/network points! bolted to ceiling and table! i'd use stainless steel instead of unistrut due to the possibility of any damp in a laundry!

2" stainless Dairy tube has the same effect of your chrome pole! the pole/tube will be very sturdy! quite easy to get hold of aswell!

 

Upvote 0 Downvote

M

maxfresh

-

Joined

Nov 1, 2010

Messages

20

Reaction score

2

Location

dublin

• Sep 29, 2012

• #9

How about a length of steel channel with angle brackets fixed to the ground , and some lid over the opening

 

Upvote 0 Downvote

ipf

-

Mentor

Nearly Esteemed

Arms

Joined

Sep 21, 2010

Messages

7,893

Reaction score

7,495

Location

Lancs

• Sep 29, 2012

• #10

Stainless steel conduit.

 

Upvote 0 Downvote

Richard Burns

-

Mentor

Arms

Joined

Feb 25, 2011

Messages

9,894

Reaction score

6,432

Location

Cambridgeshire

• Sep 30, 2012

• #11

Ackermann Hangmann overhead power module

 

Upvote 0 Downvote

A

Adam W

• Sep 30, 2012

• #12

Laptop?

 

Upvote 0 Downvote

C

cogsey133

• Sep 30, 2012

• #13

Again this goes down to cost but what about a power post. These are fixed at roof and floor height and are deemed to be semi permanent. They can easily be bought online or via cef or other well known outlets.

 

Upvote 0 Downvote