Search results

Search results

You will need 50 posts under your account before joining in with this thread because you can't link out without 50 posts first.

  1. B

    What is a 'plug in' solar panel system?

    Apparently so, I’ve copied and pasted below. Octopus Energy, named by the Renewable Energy Association (REA) as “the company that has done the most to advance UK renewables”, has made a change to its terms and conditions: solar PV systems no longer have to be MCS certified in order for end...
  2. B

    What is a 'plug in' solar panel system?

    Something that may be of interest to you?? Instead of demanding MCS certification, Octopus Energy now only requires applicants to provide confirmation of DNO (Distribution Network Operator) notification under EREC G98 or the necessary permissions under EREC G99.13 (SparkyChick - Edited to...
  3. B

    UK 32A or 40A breaker for 7kW EV Charger

    Definitely, this is why I stick to the same install procedure every time.
  4. B

    UK 32A or 40A breaker for 7kW EV Charger

    I’m sure the op said that the electrician installed a new type A RCD in existing consumer unit, also as you say the Ohme charger does have integral RCD type A 30ma and DC 6ma RCD biilt in. And as the method of installation was via swa then the charge point could arguably be connected via MCB...
  5. B

    UK 32A or 40A breaker for 7kW EV Charger

    I just had a read of their literature and as you say it “advises” 40amp. So I wouldn’t worry.
  6. B

    UK 32A or 40A breaker for 7kW EV Charger

    He has swapped The RCD out for a type A so no issue there. Sorry for rambling on a bit but RE you actual op the EV will be fine on the 32 amp.
  7. B

    UK 32A or 40A breaker for 7kW EV Charger

    Agreed. 👍. I always install separate EV board spd and type A just my preference and I’m in no way claiming to be the any better than any other. Also just out of interest (maybe your not 😂) but I notice on the EIC posted by the OP the r1+r2 of the said EV circuit is 0.67ohms. 6mm2 swa with 6mm2...
  8. B

    UK 32A or 40A breaker for 7kW EV Charger

    What do you put regarding installation method on your reports or certs? I presume you trust these 😂😂 only joking I know what you mean though. Engineering judgment is needed if only running a couple of metres through thermal insulation wouldn’t make any difference tbf if the rest of install was...
  9. B

    Induced voltage.

    Yer reckon your correct, never seen a fan running via induced voltage only ever had dimly lit LEDs. But with fans “always running” as you say timers can go bad also when waiting for an over run to stop this can seem like an endless amount of time.
  10. B

    UK 32A or 40A breaker for 7kW EV Charger

    I’d be slightly more concerned about the type of RCD present in the consumer unit. If as you say it’s 10 years old then the RCD is more than likely going to be a type AC. Bs7671 requires a type A RCD to be installed for reasons which I won’t confuse with at this point. Worth checking.
  11. B

    UK 32A or 40A breaker for 7kW EV Charger

    Fair point, but you have to trust the installer at some point. My bet would be cable cleated externally from CU to EV charger in this case. But again without seeing the install you have to trust the installers reasoning. 🤞😂
  12. B

    Derating a BS3871 following an EICR C2

    I suppose if it was supplying a fixed rate piece of equipment (I.e. less than 27 amps with correct install methods and seating factors applied) you could say it’s “ok”
  13. B

    UK 32A or 40A breaker for 7kW EV Charger

    Also fyi the cable type installed is ‘F’ so swa (steel wire armoured) with an installation method C (clipped direct) so therefore cable capable in this situation of safely pulling 53amps. So 40 amp breaker would be fine 👍
  14. B

    UK 32A or 40A breaker for 7kW EV Charger

    Has this charger been installed to an existing split load board?? I.e. one which contains 2 RCDs protected half (ish) the circuits each??
  15. B

    Derating a BS3871 following an EICR C2

    Ref method A 20 amps Ref method C 27 amps So yes I’d agree to downgrade the 32A. What to depends on the Ref method.
  16. B

    Induced voltage.

    Firstly I’d double check (presume you have) that the cores are actually what you’d expect I.e. brown -line Black -switched line & grey - neutral. Presuming these are correct and when tested the 240 does actually drop off to 37v when light turned off and timer over run has stopped. Then I suppose...
  17. B

    Induced voltage.

    I presume your are talking about a timed fan? Line/switched line and neutral???
  18. B

    Correct OCPD for disconnection times.

    Simple question (or so I thought) What would be the Correct OCPD to achieve correct disconnect times for a 200amp sun-main with ze of 0.26 tncs. What are everybody’s thoughts??
  19. B

    Icertifi EIC cert changes

    Sorry better pic of new cert layout below.
  20. IMG_6435.png

    IMG_6435.png

    • Bsharp
    • Media item
    • Comments: 0
    • Category: Electrical Videos

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top