Search results

Search results

  1. C

    Testing questions?

    TNCS systems I've seen before have not had a few strands of the sheath with black insulation, that's what's confusing me. Also, there is usually a PME warning sticker put in place by the DNO but there isn't one in this case? If I record the worst-case reference method then wouldn't questions be...
  2. C

    Testing questions?

    I haven't done any testing for a long time so some help with a few questions muchly appreciated please! Firstly, earthing. The supply cable (from underground) appears to have several strands of the sheathing coated in black insulation and which is used as the neutral with the remaining bare...
  3. C

    Export PME?

    The system was TT, but changed to PME during a change of cut-out. I called them in because the cut-out was damaged and I wanted it replaced before I renewed the CU. Never got round to measuring Ra, but will do when I re-connect, although it's probably not so important now with PME connected...
  4. C

    Export PME?

    It's running off an MCB in the house. All other circuits in the house are RCBO, so no problem with discrimination. I s'pose my question is: is there any advantage to having the PME system backed up by the earth rod? (I think so) And if not, is there a disadvantage to having the two earthing...
  5. C

    Export PME?

    Sorry, that boring subject again about which so much has been written. However, I would just like to hear views on the following: 6mm 3 core swa running off 40A MCB from consumer unit in house. Armour and 3rd core connected to PME in house. This feeds an RCBO'd consumer unit in new building in...
  6. C

    Shower interlock?

    Thanks for your comments guys... have now discovered that the electric oven is being replaced for a gas one, so feel a bit better about it now :-) still interested to know where to get hold of a shower interlock should I need one at some point....
  7. C

    Shower interlock?

    Two existing 10kw showers, will pull about 86A if used simultaneously. They haven't had problems in the past, but it's a big house which is being refurbished, including a garage to office conversion which will add extra load. While I'm at it, I wanted to make sure there's no future problems...
  8. C

    Shower interlock?

    About to do a consumer unit change and noticed that the 100a supply is feeding two electric showers. Clients say that the showers are not used simultaneously but may well be in the future. Does anyone know where to buy a 'non priority interlock' so that I can do this job properly and avoid any...
  9. C

    U/F Heating. Cable Exit?

    Most u/f elements have a 'lifetime guarantee' now so the manufacturers must be pretty confident of their longevity. I haven't done many but the ones i did almost 10 years ago are still going strong :-) Still after ideas regarding the access for thermostat cable. I was considering sinking a...
  10. C

    U/F Heating. Cable Exit?

    The themostatic probe in the floor needs to be accessable, in case it needs replacing in the future. I don't think it's good practice to plaster it in and tile over it! That's why I'm after new ideas on how people do this...surely not everyone just plasters over the wires?? :confused5:
  11. C

    U/F Heating. Cable Exit?

    Has anyone any ideas regarding the neatest way to bring the u/f cable & thermostat cable out from a tiled floor finish? :cool3:
  12. C

    Submain ?

    So, I don't need any special gland to earth the aluminium tube, and I can terminate straight into an MCB in the CU. Niceic guy also said that it doesn't need double pole protection if straight from the CU. For piece of mind I will replace the main switch in the CU with a time delayed RCD. All I...
  13. C

    Submain ?

    This surprises me. I have always assumed that being concealed in a wall, or under a wooden floor, would carry the same degree of risk. I have just confirmed with niceic guy who agrees that it seems a little silly, but you're absolutely right. :)
  14. C

    Submain ?

    If I can persuade them not to stuff the floor around the cable with insulation then maybe this will be possible! I've never used this stuff, how is it terminated with regards to the aluminium tape? Surely this has to be earthed in order for it to be suitable for use without the need for RCD...
  15. C

    Submain ?

    I have said that the cables will be concealed in the floor, under floorboards...which has the same implications as being concealed in the wall. Flexishield is great, but only upto 6mm (32 amp) which is not big enough. 40A is required here. :)
  16. C

    Submain ?

    Yes, but what about the RCD protection??
  17. C

    Submain ?

    No, I haven't considered MICC, but from what I remember the terminations will be quite bulky? The main issue here is the cable protection and shock protection. If I use swa, then I don't need an RCD at supply end but will need KMF. With this I will also need a box to terminate the swa before it...
  18. C

    Submain ?

    This is what I thought... anyone else care to comment?
  19. C

    Submain ?

    I was assuming that all unprotected cables had to be rcd'd now, are you saying that if it's over 32amp it doesn't have to be? Do you think that rather than a KMF and an rcd, a double pole rcbo would suffice? It's a bit tight so need to keep as compact as possible!
  20. C

    Submain ?

    Yes, but with this in mind then surely using twin/&earth is cheaper and easier?

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top