Hi, really stumped here. I went to replace an overhead light with a ceiling fan/light combo and got it working, but then the rest of the room didn't have power.
The fixture has power to it and then goes to a 3-way switch. In the photo, the middle black is hot and the right one is not...the...
Hi all
I have a dimmable LED light fixture in my kitchen controlled by 3-way switches (neither is a dimmer). Supply goes into Box 1, located by the sundeck door. Box 2 has the other 3-way switch, as well as a single-pole switch for a separate fluorescent fixture. The wires to the lights both...
Hello all
I need help with an electrical issue I think which is coming at my house
I have a 2 three way switch to control a light fixture in my house. Initially the 1 switch was not working so I tried to flip it multiple time, then went to another switch and light started. Again I went to my...
I am trying to replace a 3-way switch that has 2 switches on it. Total is 3 sets of 2 switches each.
Switch I am removing has a red and black wire that go to 2 black screws on the right side. Off has both switches to the left.
On the left side there is a black wire connected to the bottom of...
Hi, I am trying to wire a smart 3-way switch but the manual diagram does not make sense. Attached are photos of my existing switches and the wiring diagram from the manual. Which of my existing 3-ways do I swap out and which wires go where?
Thanks, I’ll owe you!
I have three switches on a stair well one 4-way and two 3-ways. I want to change the 3-way to an occupancy sensor switch. The switch currently has 2 blacks and red. Red to Red, Black to Black terminal, Black to gold terminal
I wired the occupancy switch in the same way and it did not work...
Hi. I'm a newbie in this forum. I'm a homeowner who's done plenty of simple lighting, outlets, etc. even including a couple of circuit breakers. I've never done a 3-way switch before though, let alone a 3-way smart switch. I've been doing my homework, but would still like a sanity check. The...
I just replaced a 3-way switch. I am 99.9% sure I wired it the same as the existing switch. Now, when this switch is in the down position the other switch works properly. When the other switch is in the up position the new switch works properly. In any other position nothing works. I connected...
Struggling with adding a 3-way switch. I have a feed with 2 wire, a 2 wire to the light, and a 3 way ran just to my new switch in one box; a simple over head light, and my second switch box with just the one 3 wire. My question is how exactly to wire at each switch, all I seem to get is power...
Hi,
I have a 3 way setup in my bedroom and would like to put in three 3-position momentary/retractive switches but was wondering how would the wiring look like for the central momentary switch or otherwise known as a intermediate switch(if was a toggle switch)?
At the moment I cannot find any...
Hi guys
I'd like to switch out the old rocker light switches with Lutron style.
The 3-way ones have terminals X, Y, Z in the picture all on one side.
The Newer style has two on the right, one on the left, A, B, C (ignoring the earth).
Could any kind person please tell me the map from X, Y, Z...
Current situation: Great room is greatly deprived of light in one-half of the room.
Solution: Add two recessed lights to the current figuration.
I'm not sure how exactly to connect the new lights to the existing lights. I have seen where some explain to connect directly to one light and not...
On my landing are three connected lights. They have 230v LED bulbs. There are three switches - one obviously an intermediate switch. In one of the four 'off' arrangements of the switches, the LEDs glow faintly. Does anyone have a theory on where this current might be leaking to? Thanks.
Hello,
Total newbie here and as you can tell from my name..... I'm definitely not an electrician. I've done a bit of electrical hackery in the past, mostly in cars and a bit of soldering, but this all feels a bit beyond my ability and I'd rather not be electrocuted and die before my 30th...
Mostly for weatherproof SWA junctions, I've tended to use Wiska boxes and piranha nuts for earthing, with gel if needed.
I have a job where I'd rather use Pratley 3-way IP68 junction boxes, no gel or resin needed, but have not used these before.
I'm wondering how long I should allow per 3-way...
I have a client who needs his hallway light to come on automatically from the front door and basement areas but switch manually from his hallway. It is currently 3-way switching with no neutrals at the swtches. His existing hallway switch is the intermediate switch. Can anybody help me with...
I am trying to replace my switches on my hall and landing with these.
2 Gang 2 Way White IQ Master Remote - Touch Dimmer (I have 1 of these)
1 Gang 2 Way Slave Dimmer (I have 3 of these)
Downstairs I have a 1 gang switch with Com, L1 and L2 controlling the downstairs light
Downstairs I also have...
Hi all,
I am not a professional electrician but I hope that some of you here might be able to shed light on a question.
vs
Basically, is there really a difference between the "pressure" on the socket if you use a 3-way adapter stuck straight into the plug (without a cord) or a typical...
HI, i have just moved into my new home and there is 2 switches that are not installed and i have tried to install them, but when i installed them switch A would be on and then Switch be wouldnt turn off the light.
right now both switches are off and the hots are merreted (1 black) (1red)
both...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc