advice | Page 10

advice

Recent contents View information Top users
  1. fluffy78

    i'm a diy guy i need some straight forward advice on a module loamp

    I have a teris lamp just like the game its made of blocks that can be changed around inside each block is 4 metal coated prongs 2 have a tiny spring that holds a removed led circuit board. One of the prongs have broken what type of strong glue could i use to refix it into place without loosing...
  2. sythai

    ECODAN ASHP... anyone hooked up one of these

    Hi Guys Just seeing anyone hooked one of these pre plumbed units up before : Mitsubishi Ecodan Assuming fairly straight forward compared some 'head scratchers' I've done recently. Possibly a power supply to inside unit + supply to outside unit + comms cable between + SL from heating 🤔 Plumber...
  3. W

    Sanity Check and Cable Sizing: Adding RV Subpanel

    Hi folks, I have been researching the NEC and forums on the Internet in preparation for adding an RV subpanel electrical hookup. I could use a sanity check to make sure that I'm buying the right type of cable(s), and that I'm adhering to code as best I can. I have 200a service to my main...
  4. B

    Gravity fed programmer wiring advice

    A question if I may before I dive in. I have an old gravity fed CH system which thanks to members here in the past - works very well. It has a Danfoss Randal 3060 programmer that has died. I have the original installation docs for the programmer - and it shows 7 terminals plus the earth. In the...
  5. richardh

    Advice on my installed solar system - missing optimisers?

    TLDR - I have a system that is supposed to have optimisers fitted, but I am not sure they have been fitted. The detail: Back in March I had a solar system installed. It was installed on two outbuildings, and as one of the outbuildings has a tree near it which can cause some shading, I was...
  6. C

    Some advice required

    Hello. I am having a problem with the electrics where I live and I wanted to ask your professional opinion. There is a plug in the kitchen that has damaged several appliances: a food processor. a kettle, a vacuum cleaner, the fridge. Also, 2 ovens that are next to that socket have burned out...
  7. R

    UPS via generator. Advice needed

    Hi All Had an enquiry about installing a generator fed UPS to a house. I have a minimal amount of experience with UPS but am certainly no expert, the ones I've been involved with were manual changeover and didn't have anything attached (generator was to be hired in the event of a failure)...
  8. sythai

    Tesla equipment advice..?

    Hi Guys On my list is sorting this right old mess out, along with a DB upgrade. Question is anything I need to aware about with this Tesla set up, guessing some sort battery set up 🤔 (not come across one yet) So I dont blow myself up and/ or mess up any of it up💥💥 Thanks Sy
  9. R

    Fitting solar advice qualifications

    Afternoon, Just looking at expanding my business and getting more into solar. I am part p niceic18th edition which means I can supply new circuit for solar up to the isolator and sign it off. Just wondering what I need to get to fit inverter legally if anything. Do I need to be Mcs accredited...
  10. J

    Advice with car charger

    Hi, I’m after some advice for an existing car charger that’s on one of our newly inherited sites. We have a Rolec 2x 7.2kw pedestal charger, just the basic model, no o-pen detection or anything like that. Whoever installed it only ran a 32A supply to it so if both sockets are in use it trips...
  11. RainbowBear154

    Need advice re fused spur switch and installing a Dishwasher

    I wonder if any one can give me some advice. I live in a fairly new build house it's 11 years old. In our kitchen there is a fused spur switch on wall above worktop and below is a socket that's connected to it this is where we have our Washing machine. Over the other side of kitchen there is...
  12. Nakulsharma647

    Made a big mistake on a job need advice

    I think i was rushing to fit a new light fitting. And got some cables trapped . Long story short light fitting smoked and went black. Have replaced fitting but really knocked my confidence is this just part of the job.feeling like a damn cowboy
  13. jasonvr

    Advice on conflict between generator interlock kit and subpanel requirements (Siemens Panel)

    I recently had my 50yr old 100A main panel replaced with a 200A Siemens panel (MC2040B1200EFC). It is the incarnation with the 200A main breaker at the bottom (earlier versions were center fed which would have alleviated my problem). At the same time I had the electrician add a 50A inlet for a...
  14. CTJXtan

    ELCD trip at my office. need help

    I live in Malaysia and this happened to the office i'm working at. There's a MCB that controls the light in room A and the stairwell. Either the MCB or the ELCB will trip randomly even though no one is playing with the switches. I tried to troubleshoot it myself. So far the situation is 1. The...
  15. highlanders317

    Advice for home pc area and extra sockets

    Hi All, I am having fibre to the premises fitted tomorrow, much earlier than expected, supposed to be another month or so. I looking for some advice on what to get to replace the current 1x4 sockets with 3 extension leads for pc, tv and always on. I am not looking doing the work myself, just...
  16. C

    Solar Panels Advice on off grid inverter wanted

    I've been asked to fit a Growatt spf 5000 es inverter which will have batteries (not sure what yet) and tied to the 230v domestic mains supply. Although I'm qualified to fit pv systems, I've never actually fitted any battery systems so not sure how they work in relation to connecting to the...
  17. D

    Advice on if quote / estimate is pricey

    Hi all, I am a new home owner and have had a quote on some electrical work I wanted done in my home. I was wondering on if someone could give some advice on if the estimate I have been given is over priced: Estimate for the following electrical work - • Full electrical installation condition...
  18. D

    Advice following EICR

    The buyer of my house has had an EICR done. I have anonymized and attached. Also the associated quote for remediation. I am wondering: surely the smoke detectors are nothing to do with it (plus, this is not a rental property anyway) it's not clear to me why the CU has to be replaced a lot of...
  19. T

    Bonding problem in restaurant

    Im an apprentice spark and have been sent to look at some bonding work at a restaurant as apparently staff have occasionally been getting shocks when they touch across metal counters. The bonding has been cut in some parts but when i trace it back rather then going to the 3 phase board it has...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top