Hi,
I'm installing a Hoover oven and would like a little help please. The oven code is HOC3158IN.
The oven manual states "The power cable must be H05V2V2-F."Also "The plug and the socket
must conform to the current norms of the installation country."
The label on the side of the oven...
Completed my AM2s start of this year.
My whole career plan is to run my own company/sole trader. Be my own boss basically.
I always get asked when I will be able to sign stuff off. So, I believe this is when I get a company setup and become a member of the competence persons scheme, is this...
Hi, can someone please advise on where if anywhere I may acquire an adapter to duct out this old Elica cooker hood. The hole is 150mm x 90mm and I can’t imagine a way of ducting out without an adapter of some sort. Does this item exist or would it just originally have come with the cooker and no...
Greetings.
I am new to this forum and I have a question regarding a relay that I am installing on a motorcycle wiring harness.
What I'm trying to do is install a momentary ignition switch, and the question is if the relay is connected correctly in this diagram.
Thanks in advance.
Hello all,
First of all I apologise if this is in the wrong forum, I figured the general forum may be the best bet :)
Thank you for taking the time to read my post, I apologise this may be a bit detail heavy but I figure if I can explain my situation then someone who has been/or is in my...
Hello fellow professionals,
I'm currently facing a challenging scenario that involves the integration of solar photovoltaic (PV) systems on roofs with complex geometries, including varying slopes and multiple obstructions like skylights and HVAC units. The project aims not only to maximize...
I am an NICEIC contractor but I have never installed an Electric vehicle charger. I have watched all of the relevant NICEIC webinars (The wire) on the subject and familiarised my self with all of the regulations etc and my next step is to enroll on some of the manufacturers online courses. I am...
Hi there,
Any advice on this would be greatly appreciated!
(Note, this is not a DIY, I'm using a fully qualified electrician, just posting here looking for advice)
We need a new fuse board fitted in a property I manage, which we hope to use for short term lets in the near future (Air BnB etc)...
I'd like to refurbish the alternator for a 2005 CR-V. My plan is to replace the front bearing (the one closest to the alternator pulley) since that's the one that has the most stress applied, and also replace the two brushes. Honda sells the brushes, but they are almost $100 for the pair! The...
Afternoon All,
Just pricing up a job and thought I'd pick your brains.
Quick run-down, Block of Flats with an underground car park. In the mains room each individual flat has a supply ran up to the flat (picture for reference) with a split concentric. The PME connection is provided within the...
Hi, I’m new to the forum. Thanks for letting me join. Asking for some diy advicd…
I’m trying to add a couple more security lights to the existing circuit but stumped at two things -
- The wires travel from the switch, to the existing security lights, then loop back (creating extra cable) to...
I recently purchased a rural property in Arizona. The property receives power from APS, the local electric utility. Power arrives from the utility meter, terminating to a 200AMP Main Service Panel in a Quonset Hut (think large garage). Inside the main panel is a 60AMP breaker that feeds a...
I am asking on behalf of a friend who has an outbuilding that he uses as an art studio, the building is fully insulated and is currently heated by 3x 2kw convector heaters.
The problem is that his heating electric costs are very high using standard daytime tariff, so I suggested to him, why not...
Hi all, I completed my level 2 2365 installation and my level 3 8202 advanced technical diploma in electrical installation and I’m unsure on what’s next. I couldn’t find an apprenticeship so I just decided to do some sub contracting work for a company, I just need some advice on what I should do...
We have had builders in, who have stopped for Xmas.
My daughter tried to do a wash. The wash machine wouldnt. Its power socket is dead. I tracked
the supply cable to its source ( on top of an eye level cupboard) & found a really frightful example of bad wiring.
Later: I tried to insert...
Hi all - relatively new to Solar but I’m looking for opinions on fitting DC SPDs on a TNCS installation.
Are we just earthing the SPD from the CU/met or does anyone fit a dedicated rod instead?
Thanks
Need advise I’m currently completing my NVQ3 portfolio. Actually nearly finished. I completed all my write ups to hit all criteria, and have been submitting to my assessor at college. The work got marked and ticked off the criteria. I’ve now come to the end and my assessor has sent my work to...
I am fixing an old BM223 for myself and have done well so far, got it a new battery holder, found the 12v zener shorted and a 1N4007 o/c next to the relay which looks to be part of that high voltage chain.
My questions are :- are there any other faulty parts to check?
What voltages would I see...
Hi guys,
I've achieved my NVQ Level 3, 18th edition and 2391-52. Looking to go off by myself, work comprising all of domestic so signing off work is needed and EICRs. what's the best route to go down? Napit or the NICIEC? or something else I'm not aware of? Cheers!
Hi everyone,
please advice and comment on the attached wiring diagram for a kitchen.
There are mixed opinions on the need for FSU-s and number of circuits required.
Distance to cu – 8m running under timber floor. kitchen size – 3.5M X 2.5M
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc