Hi.
excuse my ignorance. I have seen this before. Why is the phase in this picture taken through two of the poles in this manner?
the isolator is wired in exactly the same way with the phase going through line contact out the top and back through another pole.
what am i missing please...
Sorry for all the questions
The maximum tabulated value for a protective device is 1.85 ohms.
And the measured R1 + R2 is 1.03 ohms
What would the maximum ze 've expected to be allowed.
A) 0.35
B) 0.82
C) 21
D) 0.21
For some reason I typed in
1.03 x 0.8 on the calculator as I had the...
Just done an EICR.
Bonding to water stop cock present.
Bonding to gas. Unknown.
The gas meter is in a cupboard outside. No bonding there. The boiler is on the wall directly behind gas meter and over kitchen cupboards.
I suspect the gas pipe comes in through the wall behind kitchen...
While idle on YouTube I saw this video showing the comparison of HRC fuse and MCCB with some spectacular results at high (63kA!) but in-specification faults:
I have a Square D panel for my apartment with following breakers: 1 double 40,2 double 30's and 4 single 20. One of the 20's controls a convection cooking panel, a small toaster, an 11 watt microwave, living room lights, n HDTV and my Internet. When all the above are on, during the past few...
I have an outdoor electrical subpanel with a nearby outlet. We've plugged an extension cord with a built-in GFCI into it , but the GFCI trips every time, with any device plugged in. When we plug the same GFCI/device into a different outlet near the house, it works fine.
We've replaced the...
So my old client asked me to look at the eicr and quote he had done on 1 bed rented property to see if i can sort it. It looked like one of those in and out in 1hr report but the quote to put it all ok was over 2k for board change and sorting some high zs reading on sockets.
Looked at the...
Howdy folks. Complete electrical numpty back again with another basic question with a basic answer that I can't find an answer to elsewhere online.
I am setting up an auxiliary fuse block/relay set up on my motorcycle. I have attached a photo of what my basic fuse block/relay system will be...
Afternoon folks
I've been sat on a prickly fence since last Summer, contemplating if I should pick up my qualies again and seek out a position as a Mate/Improver.
I took redundancy last Summer from a job I absolutely hated, yet paid well. I then landed into a role I was already doing a bit of...
Hi all, apologies for another thread, I've done a search of the site and there's loads of info on here, but I'm finding bits here there and everywhere so thought id ask in relation to my situation.
I'm looking to leave my current employment, which is well paid, but I've had enough. I'm looking...
been to a job today, nothing fancy. fit 2 pendants and double dimmer,and a double socket (spurred from CU which is about 6 ft. away), in a conservatory that has had the roof plasterboarded. opened CU to find a rat's nest "installed" 2019. every terminal apart from the factory fitted ones was...
I have three switches on a stair well one 4-way and two 3-ways. I want to change the 3-way to an occupancy sensor switch. The switch currently has 2 blacks and red. Red to Red, Black to Black terminal, Black to gold terminal
I wired the occupancy switch in the same way and it did not work...
This electrical game is getting worse,in so many ways.
Wholesalers are giving us Split Db’s Rcd controlled, & these maybe obsolete soon.
Any DB with a Rcd AC type will not perform in the tripping time required if ... electronic equipment is being used.
How come they have just only found out...
Hi, and thanks for having me here....
I am considering taking one of these domestic installer courses so thought I would join up to a site like this to look around to pick up help, ideas and be realistic in what I hope to achieve.
The reality is at 45 I don't expect to switch careers and become...
After Eddie large, Bobby ball and Des O’Connor, another celeb “big” in the 70’s and 80’s has passed away.
David Prowse.... known to many as the man in the Darth Vader mask from the first three films, but also to some of us that were young ‘uns in the 70’s..... He was the original Green Cross...
Hello, thought I would join since I’ve poked around here time to time for projects but finally couldn’t find an answer this time. I have a fairly decent automotive background and I’m certified in automotive electrical. My dad was an electrical engineer back in the day and I’ve managed to cobble...
Hi all.
Friday strikes with a vengeance..
Two photos below.
Does anyone have any ideas where I can source a replacement?
Photocell for block common area lights.
Tried most wholesalers already.
Everything on market is Lin Lout and N.
ANY help appreciated.
White outer is actually...
My problem is this:
I have 2 sets of Romex 14/3 in my bathroom - one going to a light fixture, and one going to a bath fan unit (both set into the attic space). I am replacing the fan unit with another that has an integrated light (which we sorely need - the existing light fixture is poorly...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc