Hi
I am new to electrical engineering. I want to measure the 3 phase voltage near the water pumpset motors.
I have connected phase lines to earth through a diode and six 1 mega ohm resistors (measuring the voltage across resistor). The same earthing wire is connected to ground in my dc circuit...
I need a switch with two live outputs whereby I can switch between L1 and L2 but not permit L! and L2 to be active at the same time. What would you call this type of switch?
Hello Guys
Hope you are all keeping well and safe in this unprecedented times.
Just wanted some advise please. So Yesterday i had a new radiator installed but the installation required extending pipe work under the stairs near the consumer unit and where the main electric feed into the house...
Hi All. I am having my house rendered soon, before that I want to put cabling in for around 6 wall lights around the outside of the house (something like those GU10 up and down lights you see so often), obviously I want the cable hidden beneath the render however the cable won't go in...
Hi all, firstly I’m not in anyway qualified to do any electrical work but was just hoping for a quick piece of help In regard to trying to find a replacement for my non-functioning Uponor PRT-E digital thermostat which controls our underfloor heating. The model in question, the PRT-E is generic...
I purchased a 95 amp battery isolator and my alternator pushes 95 amps but I'm assuming that it may spike above that occasionally. Should I put a fuse between the two? I am only aware of 100 amp maxi fuses would that save the isolator for damage or do I need to purchase a battery isolator rated...
Hello Electricians,
This is my first post and I'm glad to be one of this forum member.
However, to clarify my question. I've a "Skin Effect Heating System", fed by 1240 V. The circuit is quit simple, Phase U, Neutral in the middle and Phase V. Phase U and Neutral feeding the heating cable#1...
I achieved my 236-1 and 2 between the years 1992 and 1997. I have just received my AM2 certificate. I have been working as an electrician for over twenty years. Can I now apply for a jib card with what I’ve got or will I need to do an nvq3.
thanks in advance.
Doing calcs on swa supply to building as sub main from main three phase squard D board for single phase supply off of TN-S supply. I used cable mate from jarsoft and looked up various tables for disconnection times. In all case scenarios it tells me it will not disconnect within the required...
Evening, is there a standard gap to put between clusters of sockets and light switches? Eg if you have a couple of double sockets, a tv socket and a lamp socket grouped together, how much of a gap would you put between them.
Also if you had few light switches grouped together what sort of gap...
Hi,
I am currently studying for my 18th edition regs update exam and came across a video by
SparkyNinja on you tube.
I think SparkyNinja is very good and produces high quality content.
However I disagree with his interpretation of regulation 434.2.1 (i)
In his video he says you need a fused...
As an electrician, do you feel you have enough independent competition between certification companies when it comes to renewal time?
(Poll total results are publicly visible - but NOT the actual individual votes - those are private and cannot be accessed via the forum software once the vote is...
I am trying to connect a smart light switch but there is not neutral. Next to the switch there is a socket with a neutral but it is under a different phase. I understand that it is the same neutral for the whole house on all phases, but when I use the other neutral, it short circuits.
I checked...
What fuse rating do I need to put in between the starter and leisure battery? I have a 12V 75AH Starter battery and 110Ah leisure battery. Cable size 16mm or 8mm. (this is for my off the grid van :) )
Can anyone tell me where to find distance between Gas box and Electric box on caravan site I know it’s 600mm, now on new install someone’s connected the boxes now between the edge of gas to edge of electric box is around 630mm but this isn’t taking in to account a socket which will be plugged in...
Hi
New here, so greetings to everyone. Fitted Labgear splitter in loft a few weeks ago to split cable from outside aerial. (One now goes to new tv in bedroom, other downstairs to main tv) Signal is ok (100% quality on all freeview channels, but signal level only about 40% on most)
Only...
I live in rural Italy. You get to chose your max KW here and pay accordingly. Most home have 1.5-3.0 kw, I pay extra for 5kw. I am at the end of the low voltage lines, one of only a few on this circuit. I constantly have voltage problems, according to my fluke multimeter it can go from 190v to...
A donut of a builder has helpfully run a piece of swa two core 16mm to a small feature fountain fitted with 1.5mm flex, suggestions on best way to join, couldn’t get the 16mm in a wago!
hi everyone, i have just got the fluke 1664fc can somone please tell me the difference between a zi no trip test and a zi trip test. i know that it in zi trip it is a high current test but still i can not understand why im getting different readings between live and earth. Thanks
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc