Hi all,
Does anyone know how to wire the "soft start" of a Bosch GWS8-125 angle grinder.
There are 3 connectors : blue wire, white wire and a plug-in connector near the blue wire (see pictures).
Thank you in advance.
B.R.
Larry.
Hi
I’ve just replaced my old Bosch dishwasher with a new Bosch one (SMV46GX00G).
It washes well and dries the dishes reasonably well, however the inside of the machine is always covered in condensation after the cycle, as the photos show.
I’ve been using the auto 45-65°C cycle, and I’ve tried...
Good afternoon all I am a new to this forum and just wanted to say Hi. I am not a electrician but a retired builder of some 6 years and still doing the odd job for friends and family . I require some help with an issue I've come across in my daughters kitchen. I'm replacing her double oven...
My Bosch 18v GSR Professional impact driver started smoking and stopped after 9 years of hard work this week. The Combi that came with it got mistreated and lasted 4 hard years. An independent tools repairer had told me the Combi's motor was no longer obtainable. Anyone out there happy...
I had to replace my old old green Bosch multicutter today at short notice and opted for the above largely due to the fact I have a fair amount of 18V batteries.
This machine is an absolute beast in comparison to my old one. It must cut through stuff at least three times faster than the previous...
I have a Boch GBH 24v 3Ah hammer drill that I considered a good bit of kit sadly the batteries have died but I still want to use it the batteries were the old NiMH new batteries are now Lithium ones. Bosch doesn't supply the batteries now however there are unbranded ones on eBay but am dubious...
Hi all,
I’m hoping someone would be able to give me some advice on Hive heating.
I have a Worcester Bosch Greenstar 30si with built in timer (however I understand this is an option that can be removed). I would like to install Hive but have no idea how to go about it.
I would consider...
Good evening all,
I have been putting it off for too long but the day really is approaching when I must replace my old faithful Bosch drill and impact driver. Not a lot wrong with the tools themselves but the old ni-cad batteries have had it and I am not prepared to replace them again.
Been...
I took the fan motor off a working Bosch built in electric oven to replace it, and now the heating element does not switch on, though if I switch the mains cooker wall switch I can hear a relay click in the control panel, so there is power going to it. The only two contacts I touched were the...
hi, I qualified as a sparks in 2008 and after doing many maintenance contracts mainly with the NHS, I only have time to do private jobs and my own. It’s currentely my own that I’m in a tiswas with. I just changed my brushes on my Bosch machine WAE 24162uk/08. They were worn right down to the...
Hi all in the forum
I have a Worcester Bosh 12 Ri condensing boiler (vented system) Installed in 2009 and the condensate pipe is leaking where it enters the syphon. The sealing device is what looks like a fibre washer., and there is an O ring at the top end of the syphon. I have the...
Hello all, recently I was installing some new downlights in a large kitchen, and trying to measure the room width/length alone was a nightmare with a tape measure so I did some research on laser distance measures and they seem to be a good way to go.
Has anyone ever owned one and are they as...
hi
I have bought a Bosch gas 35m dust extractor and a makita wall chaser, however the hose for the Bosch Hoover does fit the afptir on the wall chaser, any one else has this problem, any tips on getting round this, is there some sort of adaptor?
Thanks
Craig
I’m looking to self install a Nest Learning Thermostat on my Worcester Bosch 280 boiler, mainly as it’s a rented house, and I need to be able to remove the Nest when I leave, or when the boiler is serviced.
The wiring looks straight forward, but I just wanted to sense check before I go ahead...
Hi All,
Hive Worcester Bosch RD532i Boiler and TR2 thermostat.
I am replacing the TR2 with the Hive 3rd gen Link and Thermostat,
The boiler has 3 wires connected to the existing therm, Which ports in the Link do i connect the 3 wires to, or which wire do i lose?
I have attached photos for you...
I have an old Worcester Bosch 280 combi. Currently it doesn't have a stat connected so the connectors on the board are
N (Unused)
1 & 2 (marked as Room Stat) are jumpered, and I get 240V from 2 when metered out, but nothing from 1 (assumed to be stat switch on)
3 is unused and unmarked
4 is...
Neil Potter
Thread
bosch
cable
combi
heat
marked
nest
right
unused
worcester
Hi to all I need a bit of help please I hate wiring for heating but it's for my mate as the plumber hasn't sorted it
Right he has got a new Bosch combi boiler and with that a linked in unvented cylinder
I have no idea really how to wire it up and my mat has got both hives one for just combi...
I have been searching for somewhere in the Uk which sells the Bosch CSM180 metal cutting circular saw, without success. The yanks have had it for a while now, but I can't find it anywhere in the UK, I would like to know, has anyone out there seen it here??? All my 'stuff' is Bosch and I would...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc