Hi everyone.
I'm new and after some advise please
I am putting security lights up at my house. They are the sensor type. They didn't come with the cable so I went to my diy store and asked for the right cable to use.
I have wired up the light as per instructions.
The other end I...
Zs of 103.00 at the sockets in a third floor flat;
(that's been lived in since it's conversion in about 1960 ish) ill go hunting for the source see if i can see the problem...................found the cellar...........ah yes..... AND a recent addition for outside power! the grey / green cable...
Hello, I am wiring single phase circuits from a new 3 phase board but another electrician on site said i cant wire the circuits in brown (for live) blue (for neutral) green+yellow (for earth) on L2 or L3 as it isnt the correct phase colour.
I debated that brown is a phase colour. whats the...
Hi I'm Evan, new to the forum.
Today I was going to replace my security light at the rear of the house, due to the PIR not working.
I believe it feeds off a socket in the kitchen, done by an electrician a number of years back. It also has
a switch for it on the kitchen wall, so it can be...
hi very informative site so I'm sure someone will be able to help, I am fitting a ceiling fan with light fitting in bedroom .On removing ceiling rose I find that last tenant has removed the sleeve from the black hot wire ,as there are 3 blacks 1 being neutral as I tested this with electrical...
Hi all. First post here and I hope someone can help me out please.
My existing outdoor PIR light died and I have a new one to fit in its place.
The old one not only worked automatically on PIR mode but the 2 way switch which controlled it could be left in either 'auto' mode for PIR or switched...
Hi all, I am currently in training as an apprentice electrician, and so am constantly trying to improve my understanding on domestic circuitry, one circuit that bothers me are lighting circuits and the many methods of wiring them, at this present time I can understand how they work but still...
I wanted to post in DIY section but can't do a new post so I will do it here. I bought a 2 way outdoor switch from Maplins. I have wired the power supply as per instructions but those for the appliance do not make sense to me. here is what I have done so far:
This would appear to be correct...
Hi there, I'm currently in my 4th year, been given a job which includes wiring up the heating. Don't have any real experience in this area soo help would be much appreciated.
2 combi boilers feeding
2 seperate heating zones with rads, a underfloor heating zone and a hot water circuit which is a...
A housing rewire specification says you have to use brown plugs and 5mm screws, would you comply ? would it make you think anything about the rest of the specification document ?
Hi. I ve purchased two of these ballast, reflector lamp kits. Internally they are already wired, but i need to wire the socket and extend the cable. As you can see in the photos there are two cables coming into the ballast. The only reasonable explanation to it is that they were connected in...
I am testing a property that has the following problem -
There are three switches, one two gang two way at the bottom of the stairs (call it hall) - controlling hall with one, landing other
One two gang two way at the top of the stairs (landing), controlling hall with one landing with the...
Hi all, I do apologise if this has been posted before, But I'll be damned If I can find it. I have my AM2 this week, and I'm fairly confident In all aspects of it (Famous last words). But I've just hit a snag while trying to work out the lighting.
Apparently the circuit is a 2 way and...
Hi, could someone help me out with wiring up a switch please. We have a very dark cupboard below the stairs, and I want to install a light that will come on when the cupboard door is opened. I was planning on plugging a cable into a nearby wall socket, and running that into the cupboard to...
Hi All
I am not interested in carrying out any electrical work myself but have had some experience on a basic level and have discovered something that raised my eyebrows recently.
I recently had somebody come and install lighting and power sockets in my garage, all cables are run through PVC...
A guy at work shown me a length of cable with a plug with 5 ports (to connect to heater) and 5 wires on the other end. Apparently the heater has a stat on it.
Just wondered if any you gents knew what happens with the black and grey wires?? Thanks again.
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc