busbar | Page 4

busbar

Recent contents View information Top users
  1. O

    RCBO for this CU?

    Being lazy (yes I know) but I'm so, so busy at the mo! Need to find a 6A RCBO to fit this board, can anyone point me in the right direction? Thanks......
  2. B

    starbreaker mcbs

    Job yesterday finding fault on RFC. All good found problem, sorted, turned main switch back on packing up tools tennent says no power to upstairs lights and to combi boiler. Checked board nothing off. Quick check at pendant in bedroom no power same at fcu for boiler(on own circuit). All other...
  3. A

    Is This A RCCB Fault?

    Good evening all! I have discovered this evening (whils't re-setting the RCD) that when applying light pressure to the RCCB in my Crabtree Starbreaker CU, the connection into the busbar arcs severely and all circuits on this side of the CU flicker. I have tried re-seating the RCCB but has made...
  4. W

    removing & reinstalling tap off box for overhead industrial busbar 400v

    I have to remove a tap off box from a 400v overhead industrial busbar system , just need to know if there is a set procedure for the removal and installation of the tapin box
  5. 10linepoet

    CANALIS BUSBAR tap off box

    KU type tap off box (180amp) part number KUO-SK-57000 £30 o.n.o + £15 postage and packaging
  6. J

    divide 3 phase+n into 6 flats and a landlord

    i want to know if anyone divide 3 phase+n into 6 flats and a landlord? i wanted to use 125a 3p+n isolater and a 200a 4 pole busbar chamber. from there to meter tails. my client wants to use edf energy. uk power networks already brought the power. i just dont want to spend a grand then edf would...
  7. Dean Williams

    plug-in busbar

    Hi can someone tell me the minimum height for plug-in busbar/busway tracks. I know they come under the 'placing out of reach' heading because of their exposed terminals and the ones i'm looking at in the factory look a bit on the low side. Thanks
  8. ebow72

    Busbar Trunking Tap-Off Box

    Hello there, again... Does anyone know where I might be able to buy a busbar Trunking Tap-Off Box from? I have a project I have to quote for and can't seem to find anything other than ebay, which I don't really want to use, if I can help it. I am asking as I have a college project to undertake...
  9. T

    Can you buy wylex busbar seperate from unit?

    Bloody apprentise cut the busbar to short to go to main switch, Only reaches 83A rcd and 5 MCBs. Anyine know were i can buy a new one from if possible??
  10. D

    RCBO's on under floor bus bars

    I've been asked to spec up a job at a newish office block. Raised flooring has been installed with bus bars and tap off leads. Bus bars have been installed using 10mm swa with 63amp MCB, tap off leads have 32 amp unfused plugs on them.. There are about 12 floor boxes per bus bar and 4 bus bars...
  11. R

    Wylex busbar?

    Any body in the Swansea/neath surrounding area`s have a Wylex busbar at least 7 ways lying around that I could buy off you or know where I could buy one? Thanks
  12. P

    Busbar clamps

    Any one had any dealings with busbar clamps iv got to travel up to Scotland to fit a 3 phase isolator to busbar. is there clamps that will fit most busbars and do you just ring crimp to clamp with cable. By the way it's only a 30 amp isolator. Can any one advise
  13. R

    32a busbar feeding floorboxes

    Should the busbar be fed via an rcbo or not
  14. V

    MK dual RCD busbar help

    Hi all carrying on from my thread last night on testing continuity of radial circuits. I've got my MK dual RCD consumer unit and just need some reassurance to see if im correct or not. ok i've got a picture for you guys to look at ImageShack® - Online Photo and Video Hosting so on the...
  15. P

    RCBO's ?

    What make of RCBO does every body use ? based on reliability and cost who comes out the best ?
  16. S

    OLD OLD industrial busbar trunking.

    Hi all, I am having some concerns over some busbars in a factory I am working in. They must be 30+ years old. The are 3ph+n. My concerns start with the fact that there is no data plates to be seen. So no manufacturer or ratings no nothing. My second concern is with the earthing.... The...
  17. Jimmy Boy

    Prior to doing a board change

    As my experience is mainly maintenance related and I am now venturing into board changes for the Part P registration process I would be grateful for heads up on your 'To do list' prior to changing the CU. 1) I will do a visual inspection of accessories and Main Bonding. 2) Check for...
  18. J

    Busbar trouble

    Hello Have got an install coming up in a couple of weeks have to remove a 3phase 40Amp supply feeding a Condenser for a multi split AC Unit What will leave me with 3 spare ways on the board but we then putting in 6 units pulling around 10-12A FLC so was going to run 3 radial circuits then...
  19. P

    new rcbo to old busbar

    what is the best way to connect a new rcbo to a old front fitting busbar any help i would be grateful
  20. L

    Pir - spot the fail competition

    Spot the fault competition:D

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top