Hi all.
just wondering if anybody has any diagrams for stop circuits which are used in school workshops etc. It has been a while since i have wired 1 and feel i need a refresher in this area.
thanks for any help.
Anyone know which makes/brands, if any, have the test button wired between L1 - L2 instead of L1 - N? I'm looking for a four pole RCD to protect a TP circuit without a neutral and still have a functioning test button.
Just had a thanks (very rare, like hens teeth!) and i got to thinking, unless you go back over your posts you never see who thanked you (unlike the "like" button).
Have i just missed where to look or can you not look up who has thanked you?
hi all got a weird fault on a rcd s/o in a shopping centre, the fault is this when a walkie takie is opoerated within the vicinity of the rcd s/o the rcd trips out ( NO JOKE ) any advice on this apart from changing the walkie talkies or replacing the s/o i would really more than anything like...
Looking for one of these. Have found one on ebay, but thought i'd check first to see if anyone has any or knows or anywhere else selling them.
MEM PUSH PLUG IN 30 AMP MCB B30 FUSE CIRCUIT BREAKER A | eBay
Hi Guys
Don't know if this has been talked about before, so apologies if it has.
Was wondering if it was possible to have more than just a "like" button as sometimes it just does not seem to do justice to some of the comments.
Could we have a "Brilliant" button?
Or maybe a "Laughed out loud"...
Hi Guys
Did a small job in a house - one additional socket. Then did an RCD test - x1 (240 mSec) and x5 failed miserably. did the test a couple more times. Some improvement but still failed. The RCD is an old Wylex WSES 80/2 so replacement means a new CU. Customer asked me to test it again - it...
Hello, ive just been at a job today which i will be returning tomorrow which i have a problem with 2 Ring mains on the RCD,
*1 RINGMAIN 1
*2 RINGMAIN 2
Now when i switch on the RCD, and NO mcb's are on, the Test button doesnt work, and its the same when the mcb's are switched,
Then i tried...
Hi all,sorry if this has been posted before but just thought I,d bring it up anyway as it seems kind of important.I have just recently read an item in a magazine and it mentioned that a few people had had RCD,s blow up when they pressed the test button,didn,t mention any specific make of RCD but...
A friend of mine has a 3phase roller door. Under normal circumstances you press the up button and it opens and continues to go up untill the limiter switch kicks in. When it comes down you have to press and hold the down button. I guess this is for safety reasons.
The up button has stopped...
Hi guys,
Been getting a bit of practice with my new Metrel MI3000.
Most functions are fine, but I'm a little confused by the Z Loop impedance test.
In the book, it shows the Line, Neutral and PE probes being connected to their respective terminals on the board.
When I do this and press test...
Hi just a quick question here, i have to make a small control panel which will have a N/C contactor which will open by the use of a keyswitch to test the batteries of a charging unit. The consultants have asked for a power on indicator from the two supplies operated by the contactor, which is...
hi any body help i have a ever solar eye wireless moniter can any body tell me a easy way to get it to communicate with solar bee so i can moniter my inverter i have allready spent hours on this any help much appreciated ps i seem to have followed instructions but no joy thankyou.
I was wondering if any one has installed anything like what I have been asked to do.
It is in a training enviroment and they would like approx 5 sockets installed allong a wall that can have the power switched off via an emergency trip button by the teacher if required.
I was thinking a radial...
Hi
I went to a clients property to look at why two of several storage heaters were not working. To establish if the power is getting to the heater I poked the boost button to power up the heaters and nothing happened. Am I daft or what?? This is what the boost button does ?? I'm not waiting...
Came across the above RCD whilst working on a TT system. It had no indication of tripping currents on it. There was no main fuse so I need to record it's details including BS number. I tested it with a 30mA ramp test and it did not trip. So I fitted a 30 mA RCD to the shed supply I put in...
hi all, think i am have a blonde day today, went to do a fuse board change in some bedsits as the builders had been thrown off site (have covering letter from the local council to carry out works)
basicallly all wires prepared at board but no board, so installed a 16th board and can't get the...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc