I want to change my plastic light switch faceplates with metal ones, what size of earth wire do I buy to connect to the faceplate? and is it measured by the voltage it carries or the thickness of the copper wire?
I need to make up some connectors for testing, anyone know where I can buy to keep costs down? 415V 5 pin as well as 2P + E. While I'm making them up i'll get a 125A as well - costs start to creep up at this point though.
Where's best place to keep cost down?
Hi can anybody help i am looking to purchase a mft tester and i have a budget of £450 i have looked at a Kewtech KT63 and a Metrel MI300/MI3100 not sure wich one to buy hope you can help.
can anyone advise me of the best place to buy some electricians tools from, price, quality wise. as have got some side cutters pliers neddle noses and set of screwdrivers but need to save money for a tester and want to know the best one out there and where to get it from.
Cheers
I thought this would be an easy task but can't seem to find anywhere near me (uxbridge w/London) that I can buy a zone 1 quad LNB off the shelf and don't have time to order 1 online. I have never fitted one before but hoping I can figure it out.
Any advice on a wholesalers would be appreciated...
Currently using an old Seaward/Di-log 1000x and am not sure if it'll meet current requirements.
I do only between 1000-2000 appliances a year to keep my current customers happy.
Can someone recommend what new tester would suit best. and some guide to prices?
Downloadable would be nice, but...
as above i've a job to quote and have no idea how much a lamp post costs. its the conical type approx 8m in height. anybody know where i could get a price on 1? im located in manchester.
Hello there everyone,
So I'm looking to get an estate car as I have a wife and little daughter and can't afford a van AND a car and even those car-derived vans with seats are well expensive to insure for me. New driver with no 'no claims' etc what a headache!!
So I am looking for something...
I have a 100KW installation coming up next month. The DNO require an additional G59 relay to be installed, although the inverters are G59 already. I was just wondering if anyone recommends a good place to buy one.
I have 5 Mastervolt CS20TL inverters that will be installed. Is it just the...
Hi
could someone please tell me were i can buy a 6A Type B RCBO BSEN60898 6kA for a British general board
I bought the board from scr?????
and just tried to get a RCBO and theyre out of stock typical
does anyone else know who sell these devices
thanks
i was just wondering where do people buy there s type td rcd's from? there seems alot of different prices on line from 30 pounds to 80 pounds.
i have split load cu with two 63 amp 30ma rcd's on a tt installation, original rcd is 80amp 30ma so trips out when a fault.
could i use 80 amp stype...
As above, I have a customer who has a 4 way wylex Rewireable board at the moment. Its in his porch and the porch is tiny so space is at a premium. The smallest I can find is 10 way, is there any other make that is smaller?
Cheers :wink5:
I have just had the dreaded call from the repairers saying that my Metrel tester is knackered as it was dropped last week! The cost to repair it is about £100 short of a new one and they only give a 3 month warranty on the repair. I think I want a new one as I may be able to get an extended...
any suggestions on what tester to buy ? i wont be doin much testing its only for my own work in domestic properties but i want a 1 for a good price, not to hard to use and is not gona break after a few weeks.
I am going to renew the output shaft bearings on my Disco, I need a slide hammer which is not difficult but I need to make a "end" for it any one know where I can get steel tube threaded on the inside, not BSP or any weird stuff 22mm I think but I can confirm that later, I have made up ends...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc