can't | Page 4

can't

Recent contents View information Top users
  1. T

    Roberts Play 10 DAB Radio -- Can't Reset to Factory

    This little radio is 2 or 3 years old and very handy for portable DAB. I use 4 x rechargeable AA batteries. Not mains-operated. There are 3 station presets but I can't erase them or even factory-reset the radio. It will accept a new station to any preset but the memory of it is lost on...
  2. DavidSpark

    Cable that can't be removed

    Okay, so bare with me here. Domestic is not my bag at all, and I'm not quite sure what the best course of action would be for this. So my father has asked me to take a look at the outside light for the back garden, he would like it changed to a new one as the old one is tired and worn and is...
  3. O

    You can't polish a xxxx

    Sitting here doing an estimate. Flat in not so nice area, and this is the spec for the average sized living room: 6 x downlights 6 x wall lights 4 x low level recessed lights 1 x 3G switch inc 1 x dimmer I suspect this is being done up as a rental so I would suggest: 1 x pendent 1 x on/off...
  4. R

    What is going on, surly this clown can't be for real?

    Quoted this job Friday for a board change, customer has shown me the work completed by the last electrican. He has used 10mm clips for the 2.5tne that comes direct from the sockets.
  5. Pete999

    Pete's Videos Got a cable you think is live but can't find which CB controls it? try this for a laugh

  6. M

    Can't go wrong, bargain

    NWS SIDE CUTTER , VDE 6 In 1 Cutter 190mm, + NWS WIRE STRIPPERS BARGAIN PRICE | eBay - http://www.ebay.co.uk/itm/NWS-SIDE-CUTTER-VDE-6-In-1-Cutter-190mm-NWS-WIRE-STRIPPERS-BARGAIN-PRICE/252783887393?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
  7. B

    Can't find any cheap G4 LEDs that run off the mains 240v.

    Hi everyone We have a couple of NEXT ceiling lights in the living and dining room. Both the transformers have gone and replacement transformers are about £35 each, however I'm worried they may keep blowing and its going to get costly to replace them often. A friend suggested removing the...
  8. R

    This can't be right!? Wireing under sub-floor

    Took up the carpet as I am laying some wood flooring on my landing, I need to isolate the creaking and moving parts prior to laying the new solid wood tounge and groove. Discovered this <picture attached>. I had some work done a couple of years back to place wired smoke alarms in every room, It...
  9. Pete999

    Why can't I any more??????????

    Look at profiles and unanswered threads any more?:(
  10. S

    I can't view attached photos (and I'm not in restricted areas)

    As per the thread title, I can't view attached photos in any forum - I get directed to the "Page not found" page. For example in the "dodgy trade pics for your amusement" thread in the General Electricians Talk Forum, I can't view any of the attached photos. I've had a search through the forums...
  11. D

    Microwave above sink

    Hi all, Was out looking at a job today in a clients office, and have been asked to quote for installing an additional socket for a microwave. They have installed a shelf directly above the kitchen sink and have placed a microwave on it - present cord is stretched out across to a worktop...
  12. R

    new rules and regulations

    been told that there is new rules and regulations for pet testing anyone now of this as I can't find any
  13. stummish

    Final circuit & DNO cable in same trench

    Hi all bright sparks, I've had a question from a client I couldn't answer on the spot. I've done some google research but can't find an answer to this; Is there any reason the DNO cable and a final circuit be installed in the same trench? DNO cable will be in a duct, client wants the SWA...
  14. gazdkw82

    Help with 2382 17th exam

    iv been regularly doing some mock exams online in preparation for my exam next week, however there's been a few questions that keep coming up and I can't seem to find the answers. I took screen shots and below are the following questions. Could you help put me out my misery point me in the right...
  15. L

    Difficult Service head

    Hello all, I've recently put a new circuit in a house and when filling out my EIC, I needed to access the service head (attached). I'm relatively new to this and I'm struggling here. In order to access ANY part of this, you have to pull the main fuse and I had to cut a few metal tallys off...
  16. Dave

    Can you feed 2 radials from one fused spur

    Before I start, I know this is not usual but I want to know if it's against regs. I'm testing a conservatory ring, feed from a fused spur. There's a Live-Neutral IR fault between two of the three sockets. The cable is embedded in the conservatory bare block wall. If I just disconnect the faulty...
  17. Pete999

    Pete's Videos Can't sleep? watch this Geezer for 5 mins

  18. D

    Missing Certs Advice

    Looking for some advice. I did a C&G 2330 level 2 & 3 plus 17th ed with OLCI (yeah I know...) about 3 yrs ago, about a year or so before they went out of business. I was recently offered a job with a building maintenance company but when I showed them my certs they said one is missing, the...
  19. Paul Dodds

    New multifunction tester

    Hi, I'm obviously new. I'm looking at buying a fluke 1663 but am concerned that when the new 18th edition comes in it will be obsolete. Would I be better off buying a used 1653b, + calibration, and then a new mf tester when the new regs come in? If this has been covered then please feel free to...
  20. J

    wall up/down light with PIR+ manual override

    done a bit of searching online but struggling! one of those chrome up down led wall light with pir but need to have man override too- os ideally the old switch on/off 3 time jobbys

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top