Hi everybody
I'll try to put it as simple as possible.
I'm rewiring my two bed flat and want to hard wire all electric oil radiators on one circuit.
There'll be 6 Harmoni Lugo oil rads 1x1540w, 3x1100w, 1x660w, 1x500w: all together 6000 watts.
One electrician told me every radiator must have...
Hello;
I have a confounding problem with my electrical power consumption at my cottage north of Toronto.
I completely close up the cottage for the winter, only leaving the electric furnace on in the basement, with the basement mounted thermostat set to its lowest setting (ie. about 40 oF)...
Hey , new to forum so not sure how it all works but here goes
Last week the heating wouldn't come on when called for from Programmer, went into storage and opened the solenoid valve manually and the heating fired up so i assumed the motor was done, ordered a new one. It came yesterday and i...
Hi all,
I have a Nest stat, heatlink mounted and has a 4 way & earth connected with a separate 2 way connected.
2 way to go to wall stat T1 & T2 12v from the heatlink.
Earth to earth
Heatlink L to L on boiler
Heatlink N to N on boiler
Question is 2 & 3 on heatlink ( i think are supposed to...
Hello
After some reading recently, I was interested in installing Air Source Heat Pumps, as I think they are a great replacement for a gas boiler. From what i can see a GSHP is even more efficient but a bit more expensive and disruptive.
After a bit of research I realised that you need to be...
Hi everyone,
I have the above controller and want to install it on a Vaillant ecoTEC Plus 838H boiler, the programmer instructions are vague to say the least but there appears to be 2 options.
Method 1 live link pin 1 of the controller receiver and use a single wire to connector X1 connection...
Hello all,
I will try and make this a painless as possible but grateful for anyones thoughts.
I am currently contracted to install heaters for an eco company. These dimplex units require a permanent 24hr feed to operate the cpu and fan and a 20a dual feed for the heat fed from a second CU and...
My central heating is on a dedicated RCBO. The house has two other RCDs, one including the fridge, freezer and cooker. The other RCD is tripping virtually every day after the central heating has been on for 40 minutes or so. It will then often trip again after a few minutes. It can be reset...
In a way I know the answer, wall thermostat turns heating off when we have warm weather, but I look at the PC and it shows me the target and current in each room from the electronic TRV heads, and I thing if it can tell me when room is cold why can't it be connected to boiler and switch it on...
This is how I think one would need to wire Hive on the very old C Plan which has no tank thermostat, however I have been told on another forum the relay is not required, and it can be configured with software to switch pump and boiler with central heating and just boiler for domestic hot water...
Hi hoping for some help here, I turned off my boiler over xmas, came back turned it on and now it's no longer heating the store.
I've checked both off peak and boost, neither are warming, I've checked and tried to reset both thermostats on both elements, but they both seemed like they didn't...
Hi,
My daughter's wifi has gone down, all of south west London Virgin users have no wifi for past 3 days due to someone cutting a cable.
She has just moved into a house with Nest installed and is using underfloor heating to get heat.
Does anyone know how to manually turn on the heating with...
Been looking at changing a faulty timer on an oil boiler.
the current timer switches between DHW or DHW and HTG.
I cannot find any motorised valves, it looks like it’s just controlled with a room stat connected to a pump for heating and some other stat I can’t find for the water.
had a look...
My dilemma: I have Gas central heating ('S-Plan' with two port valves. Hot cylinder also has an immersion heater). No activity at the relevant zone valve when 'calling' for hot water.
Powering the Immersion heater does activate the hot water zone valve. I have a non-vented cylinder, fitted...
https://www.plumbersforums.net/threads/shower-power-booster-giveaway-competition-ends-31st-december.111068/
There's a deal on these, but even when there isn't a deal going they can be a godsend.
These little gizmos fire up the pressure of the water feeding your shower (or other taps)...
I have been asked to fit a hive multizone thermostat system on to a dual zone central heating setup..
The components are...
Logic heat 12 boiler
Honeywell st9100c single channel controller
Honeywell cm07 wireless stats..
Looking at the current wiring (see below), it appears theres only one...
Hi all, hope someone can help or just shed some light. We recently moved into a property that uses storage heaters in the living room. Now it is getting cold we need to use them, however we discovered faults, electrician replaced a part and assured us everything was in order. Have serviced on...
Hi,
I require a second pump connected to a 2nd zone.
System is S plan, just a bit stumped with how you only get the pumps on that are calling for heat with only one boiler.
Zone 1 at moment pump and boiler comes off 10 which is right but the 2nd pump has to go in 10 as the neutral and earth...
we have a conventional heating system and underfloor heating recently installed by the builders plumber - it’s all wired up (pump, valve, thermostat receiver etc..) but both the electrician and builder seem to be at odds with the connection at the boiler.
currently the boiler just has LNE and...
Good afternoon
Im in need of some assistance on a job. A new central heating system is being installed (previously storage heating) and the customer has purchased a hive multizone kit. She wants to control her heating up stairs and downstairs seperate so would need zones valves installed. I...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc