I've lived and worked my entire life in SoCal. Recently we moved to Southern Texas where there is a lot of rain (from a SoCal perspective) and constant high humidity.
For exterior building runs, I mostly see PVC instead of EMT. Is this just people being cheap? Or should EMT be avoided in...
Good evening everyone
Can any help or give me some advice please on measuring bending galv conduit.
My question is bending long 3m lengths.
Say for example you need to bend a full length. 400 mm to back of bend. If you insert measured end first into the former obviously you can bend it to 90...
We are installing a new kitchen and the electrician has supplied the electricity under the base units, there is a spur for a socket that will be installed at the end of the island.
The conduit from the floor is not long enough to reach the socket and so I have run the wire as-is in between the...
I've an otherwise small and simple job to do later, out of hours, fit an outdoor IP FSU for a small AC unit fed from an outdoor socket on an RFC, all external wall. However, because it's at an animal hospital and located where dogs get exercised I'm taking a cautious approach and doing it in...
I don't think I have worked with 32mm conduit before. Always 25mm and 20mm.
I want to contain 2 x 25mm tails and 1 x 16mm earth in some 32mm (rigid) plastic conduit. Where it comes out of the wall I would usually use a round conduit box. I cant find 32mm (plastic) round conduit boxes so I shall...
I’ve ordered some 25mm Adaptaflex but I’m struggling to find which connections I would need to go into 308/607 Wiska Boxes.
I’ve seen these but I’m not sure if they are okay:
https://www.cef.co.uk/catalogue/products/161819-m25-adaptalok-straight-fitting
Tried pulling some 2.5mm T&E through 10m of 20mm flexi conduit the other day with a draw tape, although I did succeed it was a bit of a wrestle.
Does anyone have any clever tricks to make this easier? Perrhaps some cable lube or some other smart idea.
Thanks in advance.
I need to run electrical conduit through an existing foundation. here is the catch. The exterior of the foundation is clad in fieldstone and has a bluestone cap. Cutting into the stone or notching the cap is not an option (Wife!!!!). The simplest solution would be to drill the slab in front...
Selling my Hilmor as I never use it anymore. It is the old style one with a 20mm and 25mm former all in one. So no changing of formers. Looking for £250 o.n.o. and buyer collects (by courier?)
I’ve just done an EICR on an old 2 bed flat that is wired in all metal conduit wired in singles however there are no CPC’s. The conduits are all bushed into the old rewireable board and back boxes/conduit boxes for lights and I’m getting good Zs readings at all outlets through the sockets/lights...
Hi, i am after another one of these conduit boxes, i have never seen one of these before, i have asked wholesalers and googled it for ages but no luck so far. Would be much appreciated if anyone knows the name or somewhere i can purchase one of these. Im aware i could use a T Inspection Box and...
Hi!
I’d like to install a pedestal-mounted (230 V, 30 A max - programmable) EV charger close to my driveway, which ends about 12 feet away from the house, on the other side of a landscaped rock wall of sorts. While I am at it, I would like to oversize the circuit to allow a second EV charger to...
Running some cables and fitting some back boxes to save some money in preparation for an electrician to do a 1st fix. Just wondering if there is a simple table available to show what size cable(s) will fit into oval conduit?
Specifically 2 x 6mm2 T+E cables (induction hob and oven) and 2 x 4mm2...
Hello I have an existing run of rigid metal conduit outside of my house that feeds several outdoor receptacles. There is no separate ground wire inside the rigid metal conduit. Is there a way that I can use liquid tight to run to a new extension receptacle? What I am particularly concerned about...
Hello
I am adding a couple of sockets to an old industrial installation. I am replacing the existing sockets and adding two more into the ring. The installation is earthed through the metal conduit and an RCB has been retrofitted to the circuit after the old style fuse board. Is it...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc