Hello everyone
I hope you all well,,
I have a question regarding old method install rosy lights-switch and connect in the box,I have a problem with one fault sort it ,the light doesn’t work,I needed help,I have experi connect in the switch…
Hi, I have an electrical noob question.
I have six ceramic sockets with light bulbs in the basement, mounted on the joists. Single 15A circuit. I'm in the US.
I'm considering installing a single gang electrical outlet (joist mount) on the same romex run as one of the lights for a small...
DIY: hi I’m looking for advice on how to connect an led bathroom mirror/light unit to a power source. I have a pull cord light switch and a fan switch in the bathroom and a light switch outside the bathroom that’s connected to a light switch at the foot of the stairs. Basically what I want to...
Power connection of unknown source (prob socket spur) connected to outdoor light. Can i disconnect the existing light. Connect up RCD plug and then connect a switch to control a new outdoor light like pic
Hi,
I'm looking for some guidance from more experienced hands. Have a friend who just bought a 2.2kw air compressor which is obviously blowing the fuse in the plug due to the start-up current. Manufacturers information suggests a 30a single phase motor DOL for the power rating whilst the...
Hi everyone,
I'm trying to have a clear view of is ok to connect a 1000W industrial fan to a 400W Tuya smart fan controller. I have some knowledge about the electricity but I'm not totally sure if it matters the switch load as long as the fan has is own capacitor.
I'm asking this as I...
Hi,
I’m looking at adding an external socket on my house. I have a external junction box which is fed from the main consumer unit, in the junction box is a connector block which feeds a SWA cable which goes under my patio to my garage. In the garage is a smaller consumer unit which has a socket...
having sent me megger 1720 in for calibration and asked if they could check out the loop having some strange reading or missing the pfcc and pefc not long having me megger 1720 back from calibration and they said at the time we can not find nowt wrong with it but you might have fault leads ,by...
I'm moving all the loads from my main panel to a sub panel, in order install an Enphase Enpower Smart Switch in between. The main panel is a 125A cutler-hammer combination meter/panel (MBE1224B125BTS), with a 2-pole100A breaker as the main service disconnect.
What's the best way to connect the...
I have an older home with some knob and tube upstairs, downstairs has been rewired new. I want to disconnect upstairs knob and tube. Can an electrician , junction my electric baseboard wire (all upstairs rooms have baseboard heaters to install new bedroom lights and plugs.?
I am on breakers.
I...
Just set up a Hikvision NVR and cameras for a customer. All fine except the Hik Connect app says the cameras are offline unless you are connected to the house network. Ie it won’t work on 4g or another Wi-fi/network.
I’m sure I didn’t have this problem last time I set one of these up. A while...
Hi,
I have recently purchased a new kitchen including applicances (which I am waiting to be delivered). I am looking to sort out my electrics and get the sockets and fuses in the right place.
Is there any reason why I can't plug the fridge/freezer and gas hob to same double socket?
The...
I have 200amp connection, with the meter and service disconnect at the road (see pictures). House panel is about 75 feet from the service disconnect at the road.
1) Assuming I need 4/0-4/0-4/0-2/0 AL wire sizes (considered a sub panel), exactly what type of wires are required to run from the...
Thank you for your time ? I have an oven that connecting directly to the 3-phase source (3N in the pictures below).
However, this is quite annoying, because the oven is fixed close to the source. Hence, I would like to know whether it is possible to wire as 1N instead, i.e. wiring the device's...
As seen in the pictures, I need the pigtail style connected to the other style. It needs to be fully weather proofed and safe as this is wiring for a light bar on my Jeep Wrangler. So please let me know how to safely do so, rather than just shoving the two together! Thanks in advance
I'm a bit of a gamer and over the years i've amassed a collection of consoles i'd like to have easily accessible. Now i understand that if i was to just grab an extension lead, and hook up all of them to the double socket i have nearby, that i'll likely overload the socket and this poses a fire...
Hi, currently working on a shop refurb at the moment.
It's a traditional building( bricks and mortar) with a house attached on the back.
The house and shop are on the same supply and meter for the time being. To move the project along we've had move the supply and meter to a new position...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc