Can anyone help, looking to put a 3kw system onto a container to enable me to charge electric golf karts 36/48v other than the modules would I need an inverter?
Hi all
Client requested speed controller for 3-phase/4KW/7.9Amp motor running extractor fan to spray paint booth in local car mechanics
Have been advised I require
SYSTEMAIR RTRD 14 SPEED CONTROLLER VSD VFD IMO INVERTER DRIVE FREQUENCY
Reconditioned and load tested unit available at £240.00...
Morning Forum,
i am looking for some help reference the correct wiring for my thermostat i am making a home made incubator. I am a little confused on which way round the cables should go. By the way its 220v.
i will attach the a photo of the thermostat if that helps.
Any help would be brilliant.
We are starting to install intelligent immersion controllers for PV, just wondering if anyone has done one and what VAT to charge? My buisness partner and i have differing opinions on whether it would qualify for the 5% VAT rate if we are installing it on its own.
As part of a PV system...
Hello.
I'm total newbie with dmx thing..
I have led color bar, rgb, and 6-channel dmx controller.
I'm trying to use the dmx controller faders to control the Red, Green, blue colors, simply that pushing fader up would bring color up, and fade down shuts down the light.
I'm unable to get any...
Hi All,
I was called to a fault a few weeks ago on a Duoheat. The off peak was ok but the peak side (filament on the inside of the cover) wasn't operable and there weren't any lights up on the PCB controller.
The main PCB had significant arcing/heat damage on it so I ordered 1 and replaced it...
Has anyone got any experiences with all these new products that are coming out to direct excess generated electricity from a PV system to your immersion? I'm getting a few of my customers asking about them. The ones I've found seem to just use a relay switch once there is a certain amount...
Hi, I want to connect an extractor fan to a controller with humidity sensor and run-on timer.
The connection diagram that came with the unit has me a bit confused. The live and neutral connections are obvious,
but the connector for the fan is marked as NO, NC and C, which I understand to mean...
Features
Red Wired Controller Pad for xbox 360
Compact ergonomics for comfortable play
Integrated headset port for Xbox LIVE
Adjustable vibration feedback for a personalized gaming experience
Works with most Windows Vista-based PCs
Live Headset For Xbox360
Noise-cancelling...
I installed a GJD controller some time ago but got a call saying it was going nuts, it is like the sensors are permanently picking you up cables seem clear of faults. Could this be caused by moisture in the sensor?
Can anyone reccomend a motor speed controller for a commercial kitchen cooker extractor, nothing fancy, no need for air volume sensors or tacho outputs just a single phase with pot, 16 to 20 A
Pict
Hi all
I was called out to investigate a heating matt which had stopped working. On closer investigation I found the unit and connections had melted and same for fusespur.
Could this be a fault with the matt, mayb thermostat fitted in the wrong place and not operating how it should.
Is...
I fitted 3 opal xl pirs to a job then found out that i needed to change the controller as well so i changed it no prob then got a call of the customer saying it was going nuts flashing and not working any ideas im lost?
Hi all.I need some advice from the pros.
I want to install two[2x 100W] semi-flexible monocrystalline pv-panels stitched into the bimini of my boat,using waterproof[IP68?] quick connect/disconnect couplings and do not want to have to buy expensive tools for a one of job.
The panels come...
I fitted two GJD opal xl PIR's and no matter what i do the lights controlled by these come on randomly during the day no matter how i set them or turn power on and off and ideas?
Hi all has anybody or can tell me where to get an replacement unit basically it is a 2 timeclocks controlling 2 30 amp control relays with a time-off-constant switch for each clock I think the name on the fron is Altair would appreciate any advice please
Hi I am new to this forum, would like some advice on fitting an analogue time clock to a vent axia TSC speed control unit.
Any help would be welcome. Thanks
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc