danfoss | Page 2

danfoss

Recent contents View information Top users
  1. K

    Replacing a Honeywell ST699C with Danfoss FP715Si - Help !

    Hi Just moved into a new house and wanted to replace the old Honeywell programmer. The issue i have is that for some reason when the heating is on the hot water appears to be on as well... should it be ? If i press the Hot Water Button +1hr it comes on ok If i press the central heating button...
  2. P

    danfoss 3020p replacement

    anyone replaced a danfoss 3020p programmer? ive been given a Honeywell st9400a to change to, only worried about the water only and water and heating settings, will the new programmer still work on heating only
  3. 123

    Danfoss Fp715si 2 Channel

    123 submitted a new resource: Danfoss FP715Si 2 Channel - Danfoss FP715Si 2 Channel Read more about this resource...
  4. M

    Nest 3rd Gen Thermostat

    Hi I have a Nest 3rd Gen Thermostat and am wanting to replace my old Danfoss T9000. I have remove the Danfoss from the wall however I have 4 Live and 3 Neutral wires plugged into that and can't work out where why or where they are supposed to go. Has anyone had anything similar or know what...
  5. D

    Danfoss Randall 3060 replacement

    Hi guys, I'm in need of a little assistance if at all possible. My client is looking to replace her old randall 3060 programmer: I was looking to swap it for a drayton lifestyle model, maybe a LP241. I just need a little help with the wiring as i have identified P.live (T6), Neutrals(T1+7)...
  6. P

    Retofit Danfoss with Ecobee 3 thermostat

    Hi, I have a Danfoss programmable thermostat. I would like to retrofit this with a smart wifi thermostat; the Ecobee 3. Danfoss wiring manual: http://heating.danfoss.co.uk/PCMPDF/38161v01s7-06.pdf. Page 5-10 Ecobee 3 wiring manual...
  7. A

    Glowworm 18sx boiler + Danfoss Dual zone wireless system. Water not heating

    Hi Guys, We have a Glowworm 18sx boiler. We have 2 zones - one for heating, the other for hot water. All controlled by Danfoss wall panel, thermostats & actuators ( these near cistern ). All this installed end of 2011. The heating zone has thermostat in hall while the water thermostat is near...
  8. B

    Danfoss 103 mechanical timer to FP75 programmer

    im changing over the old danfoss 103 mechanical timer over to the danfoss FP75 programmer. It is a combi boiler so hot water side wont be used just wanted to check on wiring. The connections are 103 timer common terminal 3 linked to live 'on' terminal 1 FP75...
  9. I

    danfoss thermostats

    Hi My wife and i have moved into a newbuild which has two thermostats. The first is a danfoss tp9000 and is located downstairs and the second is a smaller danfoss tp5000 model. The tp9000 has more controls and also handles the hot water. What i'm not sure about though is whether the tp5000 is...
  10. P

    danfoss hs3 wiring

    Hi I need help with this if poss moved into new house and this is what heating is wired up like... anyone know how it should be wired up... the orange wire from actuator is not connected to anything Heating does not come on when turned on from programmer i have to push lever across to...
  11. dez0178

    danfoss 103E5 control unit for central heating problem.

    Hi, My control unit is operating. The time is displaying and you can use the various functions but the problem is there is no red light illuminating and will not come on. Even the 1hr+ option isn't kicking in. The heating has been used since approx. early april. Hot water fine and so is boiler...
  12. D

    Danfoss fc 51 problem

    Hi, im currently building a panel for a customer using a danfoss fc 51 inverter. I cant get it to run or reverse in auto, when i put it into run or reverse in auto I get a kw and amp value but 0hz. When I run it in jog the motor turns at 5hz as set. The motor also works in handling mode. Any...
  13. K

    Danfoss tp9000

    Hi folks i want to use a programmable thermostat controller that I have been given to control a couple of tube heaters in a outside building the unit is a danfoss tp9000 with a thermostat the wiring on the programmer is 1 off Dhw 2 off htg 3 on Dhw 4 on Htg 5 remote sensor 6 remote sensor the...
  14. R

    How to wire a danfoss rx1 stat to an ideal logic combi

    Hi I recently fitted an ideal logic combi and now the customer would like a room stat fitted. I bought a danfoss rx1 but cannot seem to get it to work. Ive taken the link out of the boiler and wired those terminals to n and l in the receiver but it didnt work? Any help would be much appreciated.
  15. S

    Danfoss rotary actuator

    Hi all can you help please , have got a danfoss rotary actuator amb 162 plumbed into a standard s plan . It has two flexes on it . One flex has brown blue white , the other 3 whites labelled 1,2,3. Any help on where these go in the wiring set up thanks
  16. infinity

    danfoss HSA3

    I know there are similar threads but i have found different readings on the voltage, i have not had much to do with these so just thought id check.. The actuator seems to of packed in, it doesnt move in any situation, athough its been working a couple years so it hasnt been wired up wrong. I...
  17. B

    Danfoss zone valves!!

    I've just installed an s plan heating system using danfoss zone valves, the customer has rung to inform me that the boiler is staying on constantly, I made a school boy error that I noticed afterwards, I connected the heating system up using a Honeywell diagram! Can someone tell me if danfoss...
  18. E

    Danfoss cp715

    Was doing sone basic remedial work for someone today and they asked me to look at boiler as it wasnt working, hadnt been for couple of days. It's a danfoss cp715 and flashing the battery symbol. Seems no mains power. Opened up box with terminal blocks, no mains power. All ok at CU, searched high...
  19. T

    x2 Danfoss 4000 Inverters plus four panels for sale

    Hi, I have two inverters and four panels for sale. I have two schuco panels and two Risen. Not sure of the wattage at present. The box on one inverter has been opened and the other is a box I managed to acquire from another inverter of the same make and model. All of the equipment is brand...
  20. R

    danfoss rx1 and ideal isar combi boiler

    hi can anyone help me please. i am a disabled single mother and today everything was working fine with the boiler and thermostats. then i heards a puff noise and the power to my boiler went off. i have a danfoss rx1 wirless thermostat. it is fitted as described below. electric wire coming...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top