Hi guys new to the forum, have a question, just been out to a job to quote it, customer has 8inch box across the room between chimney breast above the bed with LED down lighters in, nice JCC Non dimmable ones, customer wants a single down lighter to be replaced to a dimmable one, no problems so...
I used the dimmable electronic transformer 35-105W (see picture) with a 12W dimmable ar111 LED and it dims ok. I thought that the minimum load had to be 35W?
Hi All
I have 6 GU10 downlighters that are on a single gang dimmer and works fine with normal 50w lamps. However I recently changed these to 3x3w LED dimmable lamps. But now if you turn the power down the lamps just flicker on and off !
I went to my local retailer and bought an LED dimmer but...
hi guys,
I've never installed or used a dimming lighting interface unit before, this one as numbers 1-9 on it and an lcd display. im wanting to know how this works. there is a board that is labelled up lighting system in the back fitted with breakers for isolation the spot lights in banks. does...
I have a customer who stated that she wanted retractive light switches installed before rewire started. They did not mention dimming retractive switches so I just thought they meant push on / push off retractive switches. The ones they want are BG Nexus. So anyway I roughed house out as normal...
as above, has anyone have any experience of this using touch dim switching ?
how does it work 2 wayed using retractable switches.
i was under the impression i could have a touch dim dimmer one end and a normal 2 way switch the other end, however, the lights are doing funny things, ie dimming...
HI,
I've been asked about installing a potentially large amount of downlights in a basement kitchen/dining area. There is going to be a lack of natural light and the client wants downlights to be installed and she would like them to be dimmed too.
After doing lots of measurements of the area...
Hello Guys,
i have ave a client who wants a lutron dimming switch fitted that he has already purchased and cannot take back, the problem is the minimum dimming load cannot be met with the LEDs involved, he has suggested a dummy resistor but I have never heard of it. Is there any safe way of...
Alright, well i signed up here because I have a question.
I'm new to the electrical systems etc, so here I go ;D
My light switch is a bulky switch, it sticks out of the wall (Has a white box then the cover, For EXAMPLE the plug sockets in the uk stick out of the wall, my light switch is...
High guys,
Im after the units that can be installed to assist in dimming of LED's...
Have played around and added some halogen loads which improves the situation greatly!
Lutron have specified a unit which sits adjacent to the Rania Dimmer but it's not very pretty...
So am seeing if anyone...
Will It Work ??????
Right, i have a customer who has a light fitting that has x3 watt halogen bulb light fitting run from a normal dimmer atm.
They are having wardrobes fitted that will have x3 GU10 Dimmable LED down lights on the outside :omg_smile: (Must be LED as they like the day white...
Hi,
My client wants us to install some LED tubes which have dimmable drivers combatible with a 0-10v dimming control. I have not dealt with this type of thing before and would welcome some advice.
My client wants the area to be set up as follows
When no movement is detected, lights on the...
bit of a dillemma, come into contact for the first time tridonic dimmable digital ballasts, which a range of control features. since we have installed wiring for 240v dimming control we can go with that rather than DSI or DALI.
maybe its late ive been mulling it over too much but the 1000w push...
Hi Guys and Girls,
I wonder if any of you could give me any help on this. We are in the middle of a large domestic refurb and are having trouble getting the architect to specify the lighting circuit. All we have been told is that all the lights (some 260 odd in all) are to be dimmable LEDs...
i was just looking at a job today, where the push switch on the wall had the feed coming into "com" and a brown in " L1 " and blue " L2" when i took the light down it had a brown in "D1" and blue in "D2" is it possible to apply 240 volts to both those connections on the ballasts or is "D2"...
Hi
I'm Rewiring a pub/resturant complex and the owner would like to have dimmable led lighting thoughout inside
it'll be a mixture of the jcc led 7's tiltable and tracklighting with pendants with either an 8w or 11w dimmable led bulb in hovering over the tables
the'll be around 140 lights in...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc