Builder customer of mine has asked me to put 2 cold tv ' s on the wall , there are about 4 or 5 of them in an office where they share a hard drive.
They want to use a timetable programme, where they can all access and change things (dates/times etc.) , they want this to be displayed on across...
Hi guys
I'm going to be getting my driveway block paved In September. Now I want to put around 6 lights in, hopefully the block pavers can run the cable in when they concrete and stand and get them into the sleeves of the lights. Any one recommend led drive way lights at a good price?
Thanks
Can anybody help regards to the best way on how i install drive way uplighter never done these before i.e do i need to use armoured, connecting in the ground etc and working around the guys laying the driveway
cheers in advance
hello l have these specification for my motor drive system this is to be installed in a gas production facility and would be greatful if l could get help in picking the right Starting system , protection for these specifications.
The load conditions that the motor will operate in are:-
Maximum...
I'm having a new drive in a couple of weeks and I'm half thinking maybe I should put some lights into the drive but can't decide what and looking for suggestions, I could fit some walk over lights around the edge but I'm not sure how far apart these should be, I dont want to illuminate the sky...
i was reminded today about an incident that happened to me so to lighten the moods a bit i decided to post it here
last fall while out for my evening walk i was the victim of a drive by (pumpkin)
some young goofballs were riding around in pick-ups trucks wearing halloween masks and lobbing old...
Was asked to look at a fault with a pump that had been reported to have tripped a couple of times over the last few weeks. The setup is a ABB ACS 141 inverter drive(230Va.c) wired to a 2.2KW 1phase/3 phase motor, wired in delta at the motor 220v/240v supply. The pump ran up ok if not sounding a...
Driving home from work end of last week....woman pulls out of a side street like schumacher straight into side of me, i mean she literally came out at probably 40mph, guessing she hit the accel instead of the brake. Completley wrote my van off :( Shes accepted responsibilty though thankfully...
Just used some great screws self drillers they are Robertson square drive screws from
www.squarescrews.co.uk
Contact them and mention electricians forum for a discount.
Standard wood screws , self drilling and self tapping available.
Hi,
Can any one advise me about the actual damage caused to a frequency drive if flashed with 500 vdc from an insulation tester?
I have an ABB ACS800 0100 drive (100kw) that has been flashed by someone. The drive uses IGBT modules fired from a control card, will it be the IGBT modules that...
Ok, so I'm registered with Rated People. I don't use them very often but once or twice I have purchased a lead that has turned out to be very profitable. I usually get about 10-15 emails per day from them and most are just deleted however this one caught my eye! Now this isn't a rant about Rated...
Hi,
I have an industrial mixer at work that used to be powered by a dual speed motor. These particular motors are expensive and not always easy to get off the shelf in the event of a breakdown. I have replaced this a 4 pole single speed motor, controlled by an Inverter. The old motor was...
guys,
got a motor tripping an overload. Too much current is been pulled however how can I be sure its the motor and not the contactor or overload that is causing the problems. Have checked resistance across terminals and compared with a similar circuit and tbh they are the same but I need to be...
Hi sorry for my newbie question, I've a question about a star delta starter. What exactly drive the mechanical contact in contactor, is't AC 240/220V separate source from L1,L2,L3? thanks.
Hi,
I am having trouble with a 3 phase motor (about 1kW I think) and a tripping RCD. The motor is DOL started through a contactor and thermal overload.
Starting the motor causes the RCD to trip instantly. Is the starting of the motor causing this and would soft-starting the motor solve the...
Can anyone reccomend to me, iv never fitted one but heard theres not much to them, is it just a plug in job or do cables need terminating ? Any help be good cheers
Hello everyone i am new to this fourm.
I have a big problem here.
I have a zavagli santi z21 2 post garage lift .
There are two motors (Belt on each motor on each post). (Not hydraulic )
Specs -
Art:z21
Max-20A
220v 50hz
The problem is when i lift the Lift one of the motors is lifting a...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc