enclosure

  1. M

    Ip67 or ip68 enclosure

    Hi all Call to a job yesterday where the outside light wasn't working. Found this under a manhole inspection cover. It was under water when I found it full to the brim. Must of ran out of competion glans. There is a swa feed and two flexes feeding under water lights in a large water...
  2. W

    Time delayed RCD to protect tails entering a metalclad CU

    Hi Guys, A Metalcad CU is being installed on a TT system in a farm garage. Chances arew things will be rested up against the walls so a Metalclad CU has been chosen to give it protection. All circuits will be protected by 30mA RCD / RCBO. From research it seems a 100mA time delayed RCD will be...
  3. H

    Mcb,s,rcbos,etc mounted in an enclosure.

    Further to an earlier post,where I suggested using a din rail enclosure to make up a 2 phase board,in the event of a serious fault with that board, am I right in thinking that the manufacturers of the mcb,s would void the warranty,since they were not fitted in a type tested dis board or consumer...
  4. kingeri

    Extending all circuits for CU move

    I need to extend 17 circuits by about a meter for a CU move. Taking account of ring finals, going from memory there'll be about 20 cables to extend. Was thinking about using an enclosure and DIN rail, with the Line DIN rail connectors. Any advice on doing this? Is this the best way to do it...
  5. P

    Meter box enclosure size HELP!

    Hello Guys I found a manufacture that sell meter box enclosures that are very good but its a little bit bigger then an average meter enclosure. Average meter enclosure - Overall size: 400mm wide x 560mm high x 215mm deep This guy's enclosure - Overall size: type 1 - 396mm wide x 520mm...
  6. D

    RCD for TT system

    Hi all, I have just read an old periodic report that has highlighted a TT system that has an RCD main switch mounted in a non insulated enclosure (metal) as a category 2. Does it state anywhere in the reg that the RCD should be in an insulated (plastic) enclosure. I've had a look but cant find...
  7. B

    Lockable/Vandal proof fused spurs

    Hi I need some unstitched fused spurs that are to be insalled in a challenging location that has a history of misuse and vandalism. Has anyone come across any spurs that the fuse cannot be easily removed or a lockable enclosure to fit a sput into. many thanks,
  8. R

    IP66 Enclosure

    I want to install a cooler unit of Rittal make on one side of an enclosure of IP66 rating. I need to cut suitable holes to the enclosure to do this. What should I do to keep the IP rating of the whole assembly?
  9. DaveyD

    SPST Relay 230v and enclosure

    Hi Can anyone advise where I can get a 230v SPST relay with screw connectors and an enclosure? I need for UFH. Thank you in advance. Regards, David
  10. A

    Connectors on lighting circuits

    Hi all hope you can help came across a rewire were all the down lighters have been wired up with strip connectors is this acceptable under BS7671 and dose this comply as an enclosure reg 5265 good advise please
  11. M

    Garage enclosure

    Hi all, Rewired my dads garage today for my part p assessment, i bought an enclosure and a 16amp and 6 amp mcbs for the circuits within the garage. The enclosure only had the din rail in. No earth or neutral bars. The garage is fed from a 32amp mcb from the cu in the house by 2.5 mm cable which...
  12. U

    RCD after meter & before CU

    Basically old cu not enough space for rcd inside unit but meter and unit is inside cupboard. Could an rcd be placed before the main switch on a din rail? Would this conform to have it exposed in a cupboard inbetweeb meter and unit. Ideally a board would be replaced but due to time and money...
  13. I

    light fitting with choc block enclosure

    most new light fitings now seem to come with the connector block within a square enclosure or choc block. Had to fit a replacement bathroom light yesterday circular bulkhead (g9 bulb). there did not appear to be enough room for the choc block to fit. i removed the choc block and fitted wago...
  14. kingeri

    Multiple circuits in one enclosure

    So I am at a job right now to fit downlights in a bathroom (I tried to talk her out of it), and have easy access via loft above. Isolated upstairs lighting circuit. Wiring in loft is very neat, there is a Line enclosure present, all cables neatly clipped. However, on inspection I have found...
  15. W

    2 Module Enclosure

    On the front cover of May 2012 Professional Electrician shows a rather tidy 2 Mod Enclosure. Does anyone know what make they are and or who sells them? Thanks.
  16. E

    large junction box or enclosure wanted

    i've got to replace a board, it's in a stupid location (behind a garage door frame) and wants moved about 4 foot to the left. half of the circuits come throught the back of the board along with the tails and the other half are clipped to the black wall and go up. ideally i want an enclosure...
  17. S

    Single enclosure for RCBO needed!!!!

    I'm looking for a single enclosure that will hold an RCBO. Every one that my local supplier have are only big enough for an MCB! Anybody suggest a make or site where would be best to get this?
  18. T

    whats the best enclosure

    pic showsa trench in between old and new doorway under stairs.i want to run some twin and earth between the opening to sockets either side. using this job to join elecsa so wondered what i could get away with? am i looking at galv conduit? could i put a wooden board over the top? pvc conduit or...
  19. A

    Earth bar melting CU enclosure!

    A friend rang me today to ask if I could come and look at his melting CU. He said that all the circuits were holding and everything operating correctly, he only noticed something was wrong when he saw smoke coming from under the stairs!! His land lord sent round a 'Multi trade' lad to 'fix' it...
  20. T

    Enclosure Cabinets (GRP)

    I'm manufacturing modern enclosure cabinets intended for domestic and industrial use, can be installed outside and inside the buildings. My cabinets are made of GRP (glass fibre reinforced polyester) which doesn't corrode, is non-flammable and very easy to assemble, has an aesthetic appearance...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

Advert

Back
Top