error | Page 3

error

Recent contents View information Top users
  1. J

    Getting an error code on MFT

    Please go easy as I’m sure it’s a simple mistake. Anyway my MFT Megger turned up today and when I switch it to Loop L-PE or L-N it comes up on the display as Err with 3 dash’s underneath. Just wondered why this is. Thanks.
  2. static zap

    An ECHO - Electrician Talk , small error -Title side

    Most recent Poster seems to be auto-credited with being thread -creator- .... Correct ORIGINAL Thread Name + creation date. -- LHS Title side ! Original poster's Name - Disappears, replaced most recent-commenter ! ( Just notice my name on a thread - from a day before ---time travel !)...
  3. T

    Landis and gyr meter display error??

    hi all, I have had an old gent recommended to me with what he thinks is a fault on his PV generation meter (landis and gyr 5235) not sure which model. He has explained that his meter seems to be switching from displaying the current date and what he describes as a portcullis displayed on the...
  4. L

    Invertor Error - FE Not Connected

    Hi guys. So, we've had solar panels installed on the roof for about 3 years now, and just recently, had an issue where the Invertor in the loft was bleeping. Went up to investigate, and it'd stopped... So, a few days later, heard the bleeping again, went up to check, and could see the...
  5. D

    SMA 4000TL 'Insulation resistance' error

    I've recently found the green light flashing and the red light on on our SMA 4000TL with the message 'Insulation resistance, check generator' on the display. Checking the ERROROB2.CSV files I can see that this isn't the first time it has errored in this way, it has happened on odd occasions for...
  6. S

    [HELP] Grid fault / 601 display error

    Hi guys , i have a SMA STP25000TL-30 just have been newly commissioned about 15 days and just recently encountering this error ( Grid fault / 601). did any one from these group encountered this ? ty
  7. T

    Cctv Install Floureon Bad Gateway Error

    Hi I bought a cheap cctv system off eBay a floureon system my broadband is with bt I can't get it connected to the Internet it says gateway error on the dvr has anyone had same problem or know how to sort. Thanks in advance
  8. A

    error 22 on a megger MFT1720 test instrument

    Hi guys anyone know what a error 22 means on a megger MFT1720 test instrument. thanks in advance
  9. charlie76

    Is this an error in the "Electrician's Guide to the Building Regulations"

    Reading the "Electricians Guide to the Building Regulations" today (ISBN 978-1-84919-889-9) section 5.7.5 Fixed Equipment, further down the paragraph states: "Outdoor fixed equipment is not required to be protected by an RCD" That in itself does not ring correct to me I would expect an RCD to...
  10. sparksburnout

    Is this an error

    I'm a bnit bored and can't think of a proper question, so what about this one. On page 141 of GN8 (earthing and bonding), it has a nice picture of a bit of SWA. They are using the GREY core as the earth, sleeved green/yellow obviously. Now, I know it doesn't specify in the regs what should be...
  11. M

    Megger MFT 1730 - Error code 76

    Just recently bought a Megger MFT1730. It comes up with a "EER 76" message when switched on. It eventually clears after switching on & off several times an allows testing to proceed. The batteries are fully charged. Any ideas?
  12. happysteve

    Another OSG error I haven't seen mentioned... RCD and zones

    Eh up :) We all know about the duff max Zs tables in the OSG (Table B6) and GN3 (Table A4)... in fact, I've only just recently updated my GN3, and I'm pleased to say they have reprinted it and it now has the correct tables in. I've noticed in my (early-purchased, with dodgy table B6) OSG that...
  13. N

    error4 on fluke 1651b tester

    Having problems with my 1651b fluke mft when measuring my ze when i clip the croc clip on earth and touch probes on phase and neutral it shows error 4 straight away without me pressing test. I've tried this at home too on my board same thing is it time for a new tester or leads. every other test...
  14. B

    Ferroli error 41

    On hols in southern Italy and aircon has just gone down when 28 degrees indoors and all apertures shut to keep out mosquitos. Multiple indoor units with one outdoor unit which is Ferroli showing error code 41. Repair man cannot be got on Sunday night. By any chance does anyone know what error 41 is?
  15. S

    Kingspan solar thermal problem

    Hi all, tomorrow morning I'm going with a plumber to check over a solar thermal install, all I know us there's error 1 flashing and a red light. Apparently resetting no longer works. I'm guessing there'll be a dual stat setup so will make sure these are chatting as they should anyone got any...
  16. D Skelton

    Is it just me, or have Wylex made a blunderous error?!

    Anyone notice anything odd about this board, in particular the main neutral linking bar?! And before anyone asks, both the enclosure and mounting plate are steel. This has really got me questioning both my basic electrical theory, and Wylex's, because if I'm right (which I'm certain I am)...
  17. Clark3169

    NICEIC Certification Scheme Max ZS allowed on NICEIC cert seems wrong?

    Hi guys. I've recently moved from NAPIT to NICEIC I've just issued a cert. Now the circuit details are as follows. Lighting, 6amp RCBO Ze - 0.18 R1&R2 - 0.64 ZS - 0.82 Now by my understanding the max allowed ZS is 6.14 for the type of RCBO so I'm well within the allowed but on the generated...
  18. R

    Megger multi function tester - error 22

    Hi, Megger multifuntion tester (i think 1800 series, can't exactly remember) - Error 22 has appeared I think when doing a loop test but i'll have to confirm this. Tester is fairly new (6 months). Any Ideas what it means? Google wasn't much help before anyone asks!! TIA Rich
  19. H

    Fluke 1651B low current loop test problems

    Hi all, Recently, when needing to test earth fault loop impedance on a circuit with a RCBO/RCD my tester just reads >2000 for evert test, even when I know the R1+R2 and Ze are fine and when added together would be well within limits. Is there something I can do to fix this or is it time for a...
  20. C

    Any boiler service engineers on?

    Went to look at a vokera (linea I think), there was a leak from the brass body of the flow or return where it connects to the boiler base plate. The boiler is also showing fault code 28, which says is "flow and return T error". The book also says that any codes beginning with 2 is a wiring...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top