Hi folks
Was called to three storage heaters which have stopped working (all storage heaters in property). Two of the connection units into which the heaters are wired have neons, and the customer says these light up when the storage supply is on over night (so problem is not with supply or...
Hi, I added a new radial kitchen circuit at a property last week. The circuit has 1x double socket, 1x socket for an integrated dishwaher and a fused spur for a cooker hood and is protected by a 16A rcbo. When first switched on the rcbo immediately tripped. I checked all terminations, insulation...
Hi
I am new to this forum and hoping to get some advice. I tried to post in the DIY section but don't have access to it.
I recently purchased an old table lamp from ebay.
I completely rewired it using a brand new brass ES lamp holder.
The light was great for a few weeks but now the bulb used...
gunners001
Thread
electric
electrical
electrics
fault
faulty
lamp
lighting
lights
Shouldn't do it but favour for wife's mate this evening started at 7pm just in, 5 mins walk away, set off at 6.30 am this morning for a proper paid job. Extractor fan pull switch broke this morning would not shift, fan on constantly. Her helpful brother had turned off the right MCB and...
R c d tripping in main c/ unit in house think intermittent fault on cable to garage.disconected at both ends my steinel testers show fault between all conductors.my mates fluke and insulation testers show clear ,i test with mine again and fault . So when I go to get new cable I buy new fluke...
Hi all. Any one had and probs controlling leds from ss4 dusk/dawn photocells?
I replaced 3 150w metal halides with 3 70w led floods. Worked perfectly fine and the customer asked me to fit some extra led strips for his sign lighting 4weeks later (L.v complete with trannys) . The lights stayed on...
Anyone else fitted the new Channel Slim led emergency lights. I fitted 9 of them and had to replace 7 as they weren't working. One of the resisters inside is burnt out. I just hope the same thing doesn't happen again:icon9:
Markeboy1000
Thread
channel
emergency
fault
faulty
led
lighting
lights
Not sure if anyone has had problems with ps3 but il ask anyway , turns green, yellow and then flashes red... Anyone any experience or know of symptoms like this....
I was called to a property where the customer said a socket was not working.
I tested the socket, took an eli. Socket working...
CU was 17th edition so as a matter of course did an rcd test, nothing..
Went back to CU realised someone had replaced the rcd with a main switch; hence why rcd...
Hello Everyone
I was just enjoying a beer and watching and episode of Sharpe, right before a major battle when everything cut out! The RCD switch on the circuit board tripped. With everything switched off it allows me to turn it back on. Small items such as the WiFi and telephone won't trip it...
CaptainMoore
Thread
appliance
everything
faulty
plugged
rcd
switched
things
trips
when
Called out to newly installed boiler, using the old Drayton MA1 3 port valve.
When HW is on, CH is also on.
Checked all connections/wiring, all seemed connected correctly.
But, getting voltage at the white cable (HW on) at the valve.
Clearly something wrong there, as there should be no voltage...
I have a strange fault. I have a split board. 2 rcd's. One keeps tripping but other is fine. I swapped them both and the same happened with the RCD I put in the place of the first one. Rcd's seem to be fine but when installed in that position they trip but are fine when in the other side...
Hi all just a quick question, I was asked to have a look at an electric shower today that keeps tripping the breaker, ive also been told that the pull cord switch in the bathroom has previously been replaced on 3 or 4 occasions. the owner of the house said it tripped the breaker last night and...
After installing a garage unit i carried out a voltage test at the furthest point of the installation. i got a reading of 112.5 v L-N. I checked it L-E and got 242v.
I ended up back at the rcd and measured the live side and got 242v. When i checked the load side i got 112.5 v. I disconnected...
Just been to a job where the tenants are saying that a socket in the lounge looses power randomly but does not trip the MCB, it's on a ring so I took all face plates off and checked connections, did IR and got >999 and got continuity on the RFC, 245v and zs 0.39 the problem did not occur while I...
my megger 1552 MFT on the continuity tests, when I go to null the leads is showing a fuse and battery cell symbol and wont take a reading and I have to turn it off. I`ve changed the batteries and fuse but its still doing it, can anyone help.
thanks mike
My friend has an takeaway. He's food warmer stopped working.
He called me out at 9:30PM at night. I was on sight within 15mins as the takeaway was only 500m from my house.
Took 15 mins to find the fault, turned out to be the themostat relay board. Normally open contact not switching.
Told...
I have an MI 3125B. When testing for Zs at a socket I touched the test button with my thumb, the tester buzzed and displayed the 'dangerous voltage on PE' symbol. So I de-energized the system to look for the fault. There was no fault and insulation resistance at 500V DC was >999 MOhms.
I...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc