Has anyone installed on a EPDM roof (membrane). I have a customer who wants a 8 panel on his Garden Room (Eco Sheds..), I dont want to use a flat roof bracket/Tubs system as the pitch is good enough for rails direct on to the roof. Has anyone got any idea's ?
Cheers
I wonder if anyone can hlep because I am running in circles because of this.
My electrician and builder dont want to put spot lights in a flat roofed room due to risk of fire. My my readings tell me LED lights are safe and if one wants to be doubly sure can put a "hood" over the light. I am...
Looking for some thoughts and opinions on this situation.
Looked at a burn out gutted old post office with an above flat needing to be fully rewired with extensive building repairs. The ground floor will be reused as a general office when it reopens.
The D.L.O. head is situated in the post...
yesterday went to look at a kitchen that had been installed by a wren kitchen installer ,problem was there spark installed 25mm deep back boxes then half way thru squeezing the sockets and faceplates on realised the boxes were to small and left them all unfinished ......what a nightmare had to...
ml2spark
Thread
again
boxes
flat
installed
kitchen
plate
socket
sockets
Existing supply is 16mm T & CPC to 2nd floor floor flat from ground floor communal CU! Fed via BS1361 60amp, after the incoming mains have been split between 2 meters! Incoming main fuse only 60amp too!
Loop reading @ 2nd floor CU is 0.12 & PFC is 1.87kA respectively!
Bit of an existing mess to...
I have been 'given' a job (friend of friend) to install 6 panels on a flat roof at their property, i have not installed any flat mounting systems as of yet so wondering if anyone can recommend a good kit manufacturer?
Any advice appreciated.
I have been asked to carry out a rewire of a top floor flat when checking the existing supply characteristics.
TN-S with a ZE of 1.24 ohms and PFC of 1.91 KA. 1361 Type 2 with 100 amp Fuse
Should I contact the DNO and ask for them to come and check before commencing work.
Unable to treat...
Being a bit of a numpty when it comes to PV installs, I have a question: I have a flat roof 5m x 4.8m SE facing, Flat to the roof is not so good I know, but I can get away with 12 panels. If I were to use maybe 15 degree mounts I am guessing I could get away with maybe 8 panels.
If only for...
Any ideas on this one?
I am doing a survey/eicr on an intake serving 9 flats belonging to a local housing authority. The cables are early 70's 16mm/6mm T&E run through the building structure. I have assumed the maximum draw is around 30A per flat and checking the Ze values and distance it...
Can anyone recommend a good flat roof solution without penetrating the roof.
I looked at renusol consoles today, however their wind load calculation suggested I needed a ballast of 320kg in each console bucket!
This is for a building that is 30m in height, and in my opinion 44 panels with...
Hi All
I have been asked to look into putting in a CU in a garage that is likely to be converted into a granny flat in the near future. Planning on using 10mm or 16mm SWA cable (buried to 600mm) as no real idea what load is going to be if it is converted so want to take worst case into...
This is my first post, So i must say hello to all the members! :)
Right i have a few questions,
This is my first flat i have rented so i am un sure of the rules ect...
My oven trips out when it gets hot,
Its very old oven its a delonghi eoc360-1g
It bypasses the pole switch (oven switch)...
James Wright
Thread
another
cable
cables
electricians' talk
flat
live
off
oven
rcd
rented
tested
tripping
where
1st floor flat on PME supply. Service head on lower floor below G/F flat. Tails to 1/F flat some 10m away protected by switched fuse after meter. Cant see run of tails but 99.99% sure they are buried in the wall as no conduit/trunking evident and they also go through the communal staircase area...
Changing a consumer unit at a flat but have a few questions regarding earthing etc. supply is from 16mm T&E fed from the incoming supply cupboard in a separate building main supply is tn-c-s. Each flat is supplied from a 63amp switch fuse. So earthing to the flat is via the 6mm back to the...
Snapester
Thread
change
consumer
consumer unit
electricians' talk
flat
unit
I am a fairly new electrician and recently received a call out from an elderly client who says that on 6 occassions over the last 5 years there have been numerous water leaks transpiring from the flat above hers. She says on at least 3 occassions the water was pouring out from the spotlight...
blenham
Thread
electricians' talk
flat
help
help!
light
through
upstairs
water
We are looking for other options for a flat roof install either Landscape or portrait layout. We have used Renusol Consule buckets which are ok but looking for something new/ different.
Any suggestions?
Thanks
These are genuine clips from UK Council flat (Public Housing) tenants complaining to the Council about problems with their flats:
1. My bush is really overgrown round the front and my back
passage has fungus growing in it.
2. He's got this huge tool that vibrates the whole house and I
just...
steve50
Thread
clips
council
electricians' talk
flat
genuine
these
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc