installed | Page 2

installed

Recent contents View information Top users
  1. Daniel1951

    UK Outdoor sockets and lights installed but where to run the cable inside now?

    I've installed an outdoor double PowerPoint on the outside wall of my kitchen and also ran a fused spur from it for lighting in a small outbuilding, all cables in conduit. Now, I have the cable from the back of the outside sockets coming into the kitchen under the sink area, near the back of the...
  2. R

    i installed Android LCD in my car dashboard. And 2 small LCD connected

    THIS IS FOR ELECTRICAL NEWS ONLY - Only companies that wish to get news out to our members can post in here. If you're a general member looking for electrical advice then please click the main HOME button in the main menu and find a suitable forum category for your question.
  3. C

    can manrose MF100T inline fan be installed over xpelair C4TSR axial fan

    Hi i am looking for some advise regarding a bathroom extractor fan currently fitted to my new bathroom refurbishment. Problem i have is a reputable bathroom company has recently refurbished my bathroom and fitted a Xpelair C4TSR fan which does not extract enough moisture out of the bathroom...
  4. L

    New thermostat installed but not working

    Hey there, I have a Honeywell TH3210D1004 thermostat that I've replaced with a Honeywell T2 thermostat. I'm not an electrician by any means but have had some experience changing out light fixtures and such, I've copied the wiring as best as I can tell and am not sure why the T2 isn't working...
  5. A

    can I plug in a Kohler standby 14kw to my 50amp receptacle

    can I plug in a Kohler standby 14kw to my 50amp receptacle which supplies both rails in a 200 amp box (already installed interlock system for my box) installation is more than the generator!
  6. M

    Using pre installed cooker circuit for 13amp or 16amp oven.

    Hi all this is my first post. I am renewing my kitchen and at the moment I have a large cooker I'm changing it to a single oven. At the moment the cooker is on its own dedicated circuit with a 32mcb and 6mm cable going to a 45a cooker switch then going to a 45a cooker outlet plate which the...
  7. C

    Just installed a new 9.5kw shower, and sat the mcb on the bus barr, and there doesn't seem to be enough power to turn on the shower,

    Should I wire it straight to the live cable and not use the bussbarr
  8. J

    Can Landis and Gyr CM100 run backwards with a solar panel installed?

    Can Landis and Gyr CM100 run backwards with a solar panel installed?
  9. the uglydog

    Has anyone successfully installed an Elgris Zero Export??

    Has anyone actually set up one of these Elgris Zero Export Controllers? I have one but cant figure out how to get it to talk to my Growatt inverter, I’ve been told by others that have them and sales info that it communicates if I get an antenna for it but the company says it needs a direct wire...
  10. K

    Question about getting 400+ amps installed

    Hello I'll try my best to explain not the best at explaining things but I have a project i'm working on currently and that is either get 400-800 amps installed in the next house I move into or into a shed but my problem is off memory a duel wall socket has a max voltage of 15 amps and for my...
  11. R

    Are unnecessarily installed conduit seals required to be poured by code?

    In the oil and gas industry (working around hazardous areas), I commonly see conduit seals in places that they should not have been installed, but not being able to wait for the conduit to be re-done due to project startups, the seals are left as they were installed. Oftentimes, these do not get...
  12. G

    Installed a new C/U now have fault

    New here so sorry if posted in wrong place, I have installed a new consumer unit as the title says it’s a split load rcd board, anyway to the point one of the rings seems to now have a neutral fault which is taking out one side of the board I have checked all obvious things, touched no...
  13. M

    Can one 15 amp lead run two 15 amp power points

    Running from house to a van home to power van there is two 15 amp points .I was hoping to run from a single power point a 15 amp lead with a double plug 15 amp extension lead..Will I need a 30 amp lead or will i require a electrician to install something at the main box from my house
  14. S

    Gland installing

    Can you use bw glands outdoor if installing from underneath the electrical point?
  15. S

    Fixture Wiring

    Installing light fixture with one black and one white to ceiling wires of 2 black and 2 white. One set of black and white wires are hot other is not. Only one switch that's not hot when tested. 120V How do I wire?
  16. Plantman2000

    Shower MCB question after electrician installed new Consumer Unit

    Hello all. A few years ago we had a new kitchen installed and as part of those works we had an electrician in to install a new feed to this kitchen and a full new consumer unit as well. This is a metal CED branded unit with CED MCB's. We have two showers, one upstairs and one downstairs. The...
  17. J

    Installed a bathroom vent/light and it trips!

    Hey friends Installed the vent/light on 2 switches to function separately. The first switch operates the light and works fine. The second switch has 2 on/off switches. The bottom operates the vent/fan fine but the top operates nothing and trips the circuit when switched!! Maybe I wired wrong or...
  18. A

    UK is twin and eath aloud in hot tub installs

    hi, just a quick question for installing a 32 amp hot tub a friend told me it HAS to be in SWA but I have seen lots of 32 amp tubs installed with 6mm twin and earth in conduit, Is he correct? and is there anything in regulations not allowing me to use twin and earth in conduit? many thanks
  19. DaveW4

    UK Wiring in soundproofing.

    Hi, I hope you are all well. I want to ask if there are any considerations to wiring if installed in a cavity wall with soundproofing? Also, do sockets, etc. need to be incased with putty or sealed with sealant?
  20. I

    Who am I and why in EF

    Hello everyone ,Attention pls:handpointright: It's a great honor to be here:handwaving: Here is Ivian from :lightbulb:lamp factory P.R.C. If you have any question of lighting installation that I'll reply ASAP try my best. Not only is me yep we have support engineer be professional. That...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top