Hello,
While pulling up floor boards for plumbing purposes (1950s semi detached) I came across an old style junction box (black plastic and screwed) attached to a joist. This is for the downstairs lighting circuit from what I can tell (size of wires and disappearing into the ceiling in a...
I'm looking for advice on the best type of junction box for 10mm t+e shower supply. At the minute it's wired into a wall mounted switch but a pull cord is to replace this and I plan to put a jb in replacement of the switch. The shower is 37amp.
Hi There,
First of all I am not a electrician, I am a carpenter. But my client has had a recent problem with a series of lights... and I am just seeing if its something that I could possibly fix or it is something more serious and need to get a registered electrician in.
There is 7 different...
Jimmy928
Thread
box
first
going
junctionjunctionbox
light
problem
voltage
working
I went to look at a job the other day for a customer to install a Hot Tub supply in the garden. Whilst there I found that an 'electrician' in the past had extended all the cables down from where an old wired fuse board used to be located to an RCD protected CU.
It was basically a bodge where...
Vitesse
Thread
board
box
enclosure
extending
fuse
fuse board
junctionjunctionbox
old
where
wired
Why was it so popular to joint the CPC's outside junction box back in the day, answers on the back of a postcard please?
I guess they never made junction boxes with enough terminals.
I looked at a job over weekend another spark left half done, there's 2 Collingwood LED bollard lights
at the entrance to a small office, one at each side of the pathway.
Cable feeding bollards is 1.5mm 3core swa ran ducting. The bollards come with a pre-wired 2 core
flex out the back of the...
Hi all, my first post on this forum. Im a member on the VXR forums and the detailing world forums, so if anyone is on either of those, give me a wave :)
Anyway - I have recently moved into a house build in 1962. The electrics are pretty up to date, and a new CU was fitted a few years back to...
Not!!!
Found this on a recent eicr, it was feeding a couple of outside lights, there was a lid on it so I presumed it was being used in the usual way, the training centres must be so proud.
Good evening. I need to put a single spur off a single 13A socket. The original parent socket won't be used and will be hidden behind a wardrobe. I need the spur connection or junction box to be very slimline because there isn't enough room behind the wardrobe.
So...is it possible to use a...
Sorry this is a general question but for some reason I couldn't start a new thread in the DIY section;
Anyway here's my question:
I have recently had the consumer unit in my house upgraded from an od 4 way wylex to a MK 10 way RCD split protection etc,etc.
to do this the electrician had to...
Hi
can someone help please I have a outdoor sensor light connected to a fused switch in my kitchen the sensor cable goes to a junction box with the following colours red yellow blue and earth then I have a double light switch wire that also goes to the the junction box with the Same colour...
Mostly for weatherproof SWA junctions, I've tended to use Wiska boxes and piranha nuts for earthing, with gel if needed.
I have a job where I'd rather use Pratley 3-way IP68 junction boxes, no gel or resin needed, but have not used these before.
I'm wondering how long I should allow per 3-way...
Hi ,
A quick question about wiring downlighters. I am wiring college rooms, it is on price, so its kind of a rush job. There are 3 downlighters all about a meter from each other in the ceiling. The way the contractor wants it done, is loop in, loop out, meaning 3 choc boxes and connector...
I need to move a number of downlighter positions. What is the best recommended mod, should i crimp the new cables with heat shrink connectors or use maintainence free junction boxes as the old positions will be plastered over?
Hi,
Unfortunately during the installation my client moved the position he wanted a PIR light, meaning even with excess cable and due to the progress of the house, I had to joint box a cable to extend to the new location.
So, the wiring goes like this.
CCU to switch - twin and earth
Switch...
jjrules2
Thread
box
earth
junctionjunctionbox
light
lights
out
pir
switch
three
I was installing some downlighters yesterday, and noted a joint in a 10mm tw&e cable. It's the supply for the house electric cooker. Someone has used a 30amp joint box, to break into the cable to supply another point. The internal wires are exposed outside of the jb. Now clearly I can't leave...
Hi all,
I am extending the house cables to fit a new con unit about 50cm away from original fuse box, 10-way including 2 showers, max cable size 6mm.
Whats the best way of doing it? I thought of using wago connectors, correctly rated and housing it all in original fuse box housing, minus fuses...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc