Hi all!
I tried to replace toggle light switch for a rocker switch, but got no power from that breaker once it was flipped back on.
So, I re-installed the old switch and everything works fine... until I flip the switch. This cuts power to everything on that circuit, (but, does not trip the...
I need advice on a wiring problem. We are in the process of putting in an en-suite and there were a few additional bits to be added. One was some low voltage lights at floor level and a illuminated mirror. Because the walls had already been plastered the electrician suggested coming through the...
Hello to all, I stumbled upon a strange problem this morning. I wanted to change the light bulb socket in my bathroom, when I noticed that when the ground and phase wires come in contact,the fuse-box trips even though the light switch is turned off. So I took a pen voltage tester and tested all...
Hi .. I bought a smart light switch from Sonoff and would like to fix it myself
The current switch has the following wiring .. L1 / COM / Neutral
The Smart Switch has the Lin / Lout / Nin
I'm not sure which wire goes where
Anyone can advise please
Thanks in advance
Hi, I've only got 2 cables to my light switch, no earth. Does this mean I cant have a metal face dimmer switch in replacement for the plastic one that's already on?
Yesterday, I replaced a light switch (as I've done several times before). When I turned the breaker panel back on, the light was working - but now the other lights connected to that same breaker panel do not work. I re-checked all connections and reset the GFI (the outlet works) but no luck with...
Hi All,
I've searched a number of threads and can't seem to locate one that works for my situation.
There are two lights controlled by two, two-gang switches. One switch is at the top of the stairs and the other at the top, so are the lights in question.
They've not worked correctly when I...
theoretically, if i had a regular everyday 10amp 1 way switch. could i wire it to turn on 22x100w light bulbs at 230 volt supply all at once?
OR
255x typical 9w led bayonet?
helloo peeps.....new guy on the block...
I have a tracker in my van which also has a dastardly wifi at 2.43 ghz in it. it is on 24 hrs a day.
It is now beginning to show symptoms which are painful - sometimes my left eye hurts as I am driving.
it is in the glove compartment of my berlingo.
I...
Hi All,
Today I've found a faulty 1G light switch... OK, nothing strange about that!
Problem is that it's smaller than the usual 86mm square. This one is only 68mm square and I'm damned if I can find one anywhere. Must admit, I've never come across one this size before.
Anyone any ideas...
We have 2 single light switches in a box, they operate a over sink light and a garbage disposal. The disposal stopped working this morning so we went the route of replacing the light switch. My husband got the disposal to work but now the light does not work. He tried replacing the other and now...
Hi all, was wondering if is possible to wire a 3 amp table lamb directly to a mains light switch?
The light switch is used for an outside light has two brown wires going to the switch and two blue wires in a chocy block going nowhere?
Thanks.
Steve.
I'm trying to replace old 3 gang light switch to new smart light switch.
It's single pole with one breaker (switch board).
Smart switch requires 4 wires (black, red, green and white)
but my old switch only have 3 wires (black, black and green)
I connected black(top) to red(line) and...
Hi
This is a bit for my OCD, the landing light works fine via both switches but when the light switches don't lie flush when the light is turned off if that makes sense? I have tried turning off the electrics and flicking the switch but it never work so its almost like the wires are the other...
I’m changing all my light switch and plus sockets to metal from plastic. I went to change the light switch in my daughters room and behind the old plastic faceplate there there 3 brown wires, one wired into L1 and then two wires going into COM, I’ve changed the faceplate to metal and put the L1...
Hi,
I have a 3 way setup in my bedroom and would like to put in three 3-position momentary/retractive switches but was wondering how would the wiring look like for the central momentary switch or otherwise known as a intermediate switch(if was a toggle switch)?
At the moment I cannot find any...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc